INVT GD10-0R2G-2-B Скачать руководство пользователя страница 55

Страница: 55 / 125

Goodrive10 Series Mini VFD

Function parameters

-50-

Function

code

Name

Description

Default Modify

you cannot enter the parameter menu if you enter

an incorrect password. Please remember your

password and save it in a secure place.

After you exit the function code editing interface,

the password protection function is enabled within

1 minute. If password protection is enabled,

"0.0.0.0.0" is displayed when you press the

PRG/ESC key again to enter the function code

editing interface. You need to enter the correct

user password to enter the interface.

Note:

Restoring to the default value may delete

the user password. Exercise caution when using

this function.

P07.02

QUICK/JOG

key function

selection

0: No function

1: Jogging running. Press QUICK/JOG to start

jogging running.

2: Shift the display state by the shifting key. Press

QUICK/JOG to shift the displayed function code

from right to left.

3: Shift between forward rotations and reverse

rotations. Press QUICK/JOG to shift the direction

of the frequency commands. This function is only

valid in the keypad commands channels.

4: Clear UP/DOWN settings. Press QUICK/JOG

to clear the set value of UP/DOWN.

5: Coast to stop. Press QUICK/JOG to coast to

stop.

6: Shift the running commands source. Press

QUICK/JOG to shift the running commands

source.

7: Quick commission mode(committee according

to the non-factory parameter)

Note:

Press QUICK/JOG to shift between forward

rotation and reverse rotation, the VFD does not

record the state after shifting during powering off.

The VFD will run according to parameter P00.13

during next powering on.

◎

Содержание GD10-0R2G-2-B






























































































































Результаты поиска

Содержание GD10-0R2G-2-B

Отзывы:

Похожие инструкции для GD10-0R2G-2-B

Бренды по названию

Популярные бренды

INVT GD10-0R2G-2-B, Руководство по эксплуатации

Результаты поиска

Содержание GD10-0R2G-2-B

Отзывы:

Похожие инструкции для GD10-0R2G-2-B

Бренды по названию

Популярные бренды