background image

WARRANTY

TWENTY-FOUR (24) MONTH LIMITED WARRANTY

Intelligent Motion Systems, Inc. (“IMS”), warrants only to the purchaser of the Product from IMS (the “Customer”) that the 

product purchased from IMS (the “Product”) will be free from defects in materials and workmanship under the normal use 

and service for which the Product was designed for a period of 24 months from the date of purchase of the Product by the 

Customer. Customer’s exclusive remedy under this Limited Warranty shall be the repair or replacement, at Company’s 

sole option, of the Product, or any part of the Product, determined by IMS to be defective. In order to exercise its warranty 

rights, Customer must notify Company in accordance with the instructions described under the heading “Obtaining Warranty 

Service.”

This Limited Warranty does not extend to any Product damaged by reason of alteration, accident, abuse, neglect or 

misuse or improper or inadequate handling; improper or inadequate wiring utilized or installed in connection with the 

Product; installation, operation or use of the Product not made in strict accordance with the specifications and written 

instructions provided by IMS; use of the Product for any purpose other than those for which it was designed; ordinary 

wear and tear; disasters or Acts of God; unauthorized attachments, alterations or modifications to the Product; the misuse 

or failure of any item or equipment connected to the Product not supplied by IMS; improper maintenance or repair of the 

Product; or any other reason or event not caused by IMS.

IMS HEREBY DISCLAIMS ALL OTHER WARRANTIES, WHETHER WRITTEN OR ORAL, EXPRESS OR IMPLIED BY 

LAW OR OTHERWISE, INCLUDING WITHOUT LIMITATION, 

ANY WARRANTIES OF MERCHANTABILITY OR FITNESS 

FOR ANY PARTICULAR PURPOSE

. CUSTOMER’S SOLE REMEDY FOR ANY DEFECTIVE PRODUCT WILL BE AS 

STATED ABOVE, AND IN NO EVENT WILL THE IMS BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, SPECIAL OR 

INDIRECT DAMAGES IN CONNECTION WITH THE PRODUCT.

This Limited Warranty shall be void if the Customer fails to comply with all of the terms set forth in this Limited Warranty. This 

Limited Warranty is the sole warranty offered by IMS with respect to the Product. IMS does not assume any other liability in 

connection with the sale of the Product. No representative of IMS is authorized to extend this Limited Warranty or to change 

it in any manner whatsoever. No warranty applies to any party other than the original Customer.

IMS and its directors, officers, employees, subsidiaries and affiliates shall not be liable for any damages arising from any 

loss of equipment, loss or distortion of data, loss of time, loss or destruction of software or other property, loss of production 

or profits, overhead costs, claims of third parties, labor or materials, penalties or liquidated damages or punitive damages, 

whatsoever, whether based upon breach of warranty, breach of contract, negligence, strict liability or any other legal theory, 

or other losses or expenses incurred by the Customer or any third party.

OBTAINING WARRANTY SERVICE

Warranty service may obtained by a distributor, if the Product was purchased from IMS by a distributor, or by the Customer 

directly from IMS, if the Product was purchased directly from IMS. Prior to returning the Product for service, a Returned 

Material  Authorization  (RMA)  number  must  be  obtained.  Complete  the  form  at  http://www.imshome.com/rma.html  after 

which  an  RMA  Authorization  Form  with  RMA  number  will  then  be  faxed  to  you.  Any  questions,  contact  IMS  Customer 

Service (860) 295-6102.

Include a copy of the RMA Authorization Form, contact name and address, and any additional notes regarding the Product 

failure with shipment. Return Product in its original packaging, or packaged so it is protected against electrostatic discharge 

or physical damage in transit. The RMA number MUST appear on the box or packing slip. Send Product to: Intelligent Motion 

Systems, Inc., 370 N. Main Street, Marlborough, CT 06447.

Customer shall prepay shipping changes for Products returned to IMS for warranty service and IMS shall pay for return of 

Products to Customer by ground transportation. However, Customer shall pay all shipping charges, duties and taxes for 

Products returned to IMS from outside the United States.

Содержание MDrive AC Plus 34





































































Отзывы: