Intel Stratix 10 Скачать руководство пользователя

Страница: 95 / 228

4.2.5. PMA Direct 10.3125 Gbps x 4

Connect

tx_clkout

(257.8125 MHz) of each individual channel to

tx_coreclkin

and connect

rx_clkout

(257.8125 MHz) to

rx_coreclkin

. If you use any other

source for

tx_coreclkin

rx_coreclkin

, make sure

tx_coreclkin

and

rx_coreclkin

have 0 PPM difference with

tx_clkout

and

rx_clkout

, respectively.

The clocking scheme in this use case is the same as

Figure 52

on page 91.

4.2.6. PMA Direct 100GE Gbps (25 Gbps x 4 per lane) (FEC On)

This use case is implemented in the case of multi-lane protocols like 100GbE, for

example. This uses four transceiver lanes of 25 Gbps each, where all four lanes must

use the same FEC block. FEC is clocked by one of the four channels and you can

configure this in the Native PHY IP core Parameter Editor. There is an inherent

dependency between channels in this configuration. However, for applications like 100

GbE, dependency is acceptable and sometimes required. For each of the four channels
with Core Interface FIFOs in Phase Compensation mode, connect

tx_clkout

(402.83

MHz) to

tx_coreclkin

, and connect

rx_clkout

(402.83 MHz) to

rx_coreclkin

If you use any other source for

tx_coreclkin

rx_coreclkin

, make sure

tx_coreclkin

and

rx_coreclkin

have 0 PPM difference with the

tx_clkout

and

rx_clkout

, respectively.

4. Clock Network

UG-20056 | 2019.02.04

Send Feedback

Intel

Stratix

10 E-Tile Transceiver PHY User Guide

Содержание Stratix 10





































































































































































































































Результаты поиска

Содержание Stratix 10

Отзывы:

Похожие инструкции для Stratix 10

Бренды по названию

Популярные бренды

Intel Stratix 10, Руководство пользователя

Результаты поиска

Содержание Stratix 10

Отзывы:

Похожие инструкции для Stratix 10

Бренды по названию

Популярные бренды