Intel Stratix 10 Скачать руководство пользователя

Страница: 137 / 228

7.15. Transceiver Register Map

The transceiver register map provides a list of available PCS, PMA, and EMIB

addresses that are used in the reconfiguration process (the transceiver configuration

file includes details about the registers that are set for a specific transceiver

configuration). Do not use the register map to locate and modify specific registers in

the transceiver. Doing so may result in an illegal configuration. Refer to a valid

transceiver configuration file for legal register values and combinations.

7.16. Loading IP Configuration Settings

You may need to set the PMA RX adaptation settings for optimal transceiver

performance. See the PMA Tuning for more information. There are two methods for

setting the PMA RX adaption values.
•

The first method is to use PMA attributes to load the PMA RX adaptation settings

one by one. See PMA Attribute Codes and Configuring a PMA Parameter Tunable

by the Adaptive Engine for details of how to load an adaptation setting.

•

The second method is, when you generate the IP, to define up to eight different

PMA configurations in the Native PHY IP to use built-in logic to load one of them to

all transceiver channels in the instance at run-time. SeeLoading IP Configuration

Settings Process for more details and Configuring a PMA Parameter Using Native

PHY IP for an example.

Related Information

•

Loading IP Configuration Settings

on page 137

•

PMA Tuning

on page 68

•

Loading IP Configuration Settings Process

on page 137

•

Configuring a PMA Parameter Tunable by the Adaptive Engine

on page 155

•

PMA Attribute Codes

on page 170

7.16.1. Loading IP Configuration Settings Process

1. Use the control and status register 0x40143 to load a profile into the PMA.

indicates to the built-in logic to do the actual load.

2. Poll register 0x40144[0] until it becomes 1 to indicate the configuration loading

has completed.

3. Set register 0x200 to register 0x203 as indicated in Loading Parameters into the

Receiver.

4. Poll register 0x207[7] until it becomes 1 to indicate the IP configuration has been

loaded to all transceiver channels. The bit self-clears.

5. Check register 0x204[0]. A '0' indicates the loading was successful.

Related Information
Loading Parameters into the Receiver

on page 183

7. Dynamic Reconfiguration

UG-20056 | 2019.02.04

Send Feedback

Intel

Stratix

10 E-Tile Transceiver PHY User Guide

137

Содержание Stratix 10





































































































































































































































Результаты поиска

Содержание Stratix 10

Отзывы:

Похожие инструкции для Stratix 10

Бренды по названию

Популярные бренды

Intel Stratix 10, Руководство пользователя

Результаты поиска

Содержание Stratix 10

Отзывы:

Похожие инструкции для Stratix 10

Бренды по названию

Популярные бренды