Intel Stratix 10 страница 145 Скачать руководство пользователя

Страница: 145 / 228

a. Write 0x84[7:0] = 0x07.
b. Write 0x85[7:0] = 0x00.
c. Write 0x86[7:0] = 0x01.
d. Write 0x87[7:0] = 0x00.
e. Write 0x90[0] = 1'b1.
f.

Read 0x8A[7]. It should be 1.

g. Read 0x8B[0] until it changes to 0.
h. Write 0x8A[7] to 1'b1 to clear the 0x8A[7] value.

4. Wait for

tx_ready

and

rx_ready

to both be 1.

5. Set the data comparator.

a. Write 0x84[7:0] = 0x03.
b. Write 0x85[7:0] = 0x02.
c. Write 0x86[7:0] = 0x03.
d. Write 0x87[7:0] = 0x00.
e. Write 0x90[0] = 1'b1.
f.

Read 0x8A[7]. It should be 1.

g. Read 0x8B[0] until it changes to 0.
h. Write 0x8A[7] to 1'b1 to clear the 0x8A[7] value.

6. Reset error counters.

a. Write 0x84[7:0] = 0x00.
b. Write 0x85[7:0] = 0x00.
c. Write 0x86[7:0] = 0x17.
d. Write 0x87[7:0] = 0x00.
e. Write 0x90[0] = 1'b1.
f.

Read 0x8A[7]. It should be 1.

g. Read 0x8B[0] until it changes to 0.
h. Write 0x8A[7] to 1'b1 to clear the 0x8A[7] value.

7. Wait for the 32 bits wide error counter to be accumulated.
8. Set the error count to be read out.

a. Write 0x84[7:0] = 0x03.
b. Write 0x85[7:0] = 0x00.
c. Write 0x86[7:0] = 0x18.
d. Write 0x87[7:0] = 0x00.
e. Write 0x90[0] = 1'b1.
f.

Read 0x8A[7]. It should be 1.

g. Read 0x8B[0] until it changes to 0.
h. Write 0x8A[7] to 1'b1 to clear the 0x8A[7] value.

9. Read the lower 16 bits of the error counter.

8. Dynamic Reconfiguration Examples

UG-20056 | 2019.02.04

Send Feedback

Intel

Stratix

10 E-Tile Transceiver PHY User Guide

145

Содержание Stratix 10





































































































































































































































Результаты поиска

Содержание Stratix 10

Отзывы:

Похожие инструкции для Stratix 10

Бренды по названию

Популярные бренды

Intel Stratix 10, Руководство пользователя

Результаты поиска

Содержание Stratix 10

Отзывы:

Похожие инструкции для Stratix 10

Бренды по названию

Популярные бренды