Intel Stratix 10 Скачать руководство пользователя

Страница: 117 / 228

6.8. Interfaces

6.8.1. Reset Parameters in the Native PHY GUI

Table 49.

Reset Parameters

Parameter Name

Range

Description

Enable Manual Reset

On/Off

On = Use the manual reset process to reset the Native PHY.

Enable Fast Simulation

for Controller

On/Off

On = Use reduced reset timings for simulation.

Enable Fast Simulation

for Sequencer

On/Off

On = Use reduced reset timings for simulation.

Enable Individual TX

and RX Reset

On/Off

On = Use individual reset to reset the TX or RX PMA path individually.

Use Separate TX/RX

Reset Per Channel

On/Off

If you implement multiple channels in your Native PHY IP
• On = Each channel’s signals are independent from others and do not gate

other channels’ reset sequences.

• Off = If any channel’s PMA is not ready, deasserting

rx_is_lockedtodata

affects all channels.

If you implement a single channel in the Native PHY IP, this has no effect.

Enable TX/RX reset

sequencing

On/Off

On = The reset controller deasserts the TX before deasserting the RX. This

parameter needs to be set when RS-FEC is enabled in aggregate mode and

enable datapath and interface reconfiguration is disabled.

RX Reset Duration

100 ns to 1

The RX pulses the

rx_is_lockedtodata

output when there is no serial data.

The reset controller by default waits for the

rx_is_lockedtodata

to be high

for 180 μs before deasserting reset. You can set this parameter for additional

filtering.

6.8.2. HDL Ports/Interfaces

Table 50.

HDL Ports/Interfaces when the Reset Controller is in Automatic Mode

Port Name

Direction

Width

Description

reset

Input

Number of

channels

Resets TX and RX when asserted. Visible when Enable individual TX

and RX resets is disabled. When the Native PHY is configured in PAM4

high datarate mode, the bus width equals the number of data channels

parameter in the GUI divided by two.

tx_reset

Input

Number of

channels

Resets TX when asserted. Visible when Enable individual TX and RX

resets is enabled. When the Native PHY is configured in PAM4 high

datarate mode, the bus width equals the number of data channels

parameter in the GUI divided by two.

rx_reset

Input

Number of

channels

Resets RX when asserted. Visible when Enable individual TX and RX

resets is enabled. When the Native PHY is configured in PAM4 high

datarate mode, the bus width equals the number of data channels

parameter in the GUI divided by two.

tx_ready

Output

Number of

channels

Status signal to indicate when TX resets sequencing is complete.
Deasserts during TX reset assertion.
Asserts a few clock cycles after deassertion of TX resets.

rx_ready

Output

Number of

channels

Status signal to indicate when RX resets sequencing is complete.
Deasserts during RX reset assertion.

continued...

6. Resetting Transceiver Channels

UG-20056 | 2019.02.04

Send Feedback

Intel

Stratix

10 E-Tile Transceiver PHY User Guide

117

Содержание Stratix 10





































































































































































































































Результаты поиска

Содержание Stratix 10

Отзывы:

Похожие инструкции для Stratix 10

Бренды по названию

Популярные бренды

Intel Stratix 10, Руководство пользователя

Результаты поиска

Содержание Stratix 10

Отзывы:

Похожие инструкции для Stratix 10

Бренды по названию

Популярные бренды