manualshive.com logo in svg

Intel Stratix 10, Руководство пользователя

Поделиться
Скачать
Intel Stratix 10 Скачать руководство пользователя страница 132

Port Name

Direction

Clock Domain

Description

reconfig_address[log2<N>+18:0]

Input

reconfig_clk

Address bus. The lower 19

bits specify address, and

the upper bits specify the

channel.

reconfig_writedata[7:0]

Input

reconfig_clk

An 8-bit data write bus.

Data to be written into the

address indicated by

reconfig_address

.

reconfig_readdata[7:0]

Output

reconfig_clk

An 8-bit data read bus.

Valid data is placed on this

bus after a read operation.

Signal is valid after

reconfig_waitrequest

goes high and then low.

reconfig_waitrequest

Output

reconfig_clk

A one-bit signal that

indicates that the AVMM

interface is busy. Keep the

AVMM command asserted

until the interface is ready

to proceed with the read/

write transfer.

When Share reconfiguration interface is disabled and Provide separate

interface for each channel is enabled, the Native PHY IP core provides an

independent reconfiguration interface for each channel. For example, when a

reconfiguration interface is not shared for a four-channel Native PHY IP instance,

reconfig_address_ch0[18:0] 

corresponds to the reconfiguration address bus of

logical channel 0, 

reconfig_address_ch1[18:0] 

correspond to the

reconfiguration address bus of logical channel 1, 

reconfig_address_ch2[18:0]

corresponds to the reconfiguration address bus of logical channel 2, and

reconfig_address_ch3[18:0] 

correspond to the reconfiguration address bus of

logical channel 3.

The following figure shows the signals available when the Native PHY is configured for

four channels and the Share reconfiguration interface option is not enabled and

Provide separate interface for each channel is enabled.

Figure 86.

Signals Available with Independent Native PHY Reconfiguration Interfaces

Native PHY IP Core

clk
reset
write
read
address
writedata
readdata
waitrequest

reconfig_clk_ch3, ..., reconfig_clk_ch0

reconfig_reset_ch3, ..., reconfig_reset_ch0

reconfig_write_ch3, ..., reconfig_write_ch0

reconfig_read_ch3, ..., reconfig_read_ch0

reconfig_address_ch3[18:0], ..., reconfig_address_ch0[18:0]

reconfig_writedata_ch3[7:0], ..., reconfig_writedata_ch0[7:0]

reconfig_readdata_ch3[7:0], ..., reconfig_readdata_ch0[7:0]

reconfig_waitrequest_ch3, ..., reconfig_waitrequest_ch0

Note: 

The RS-FEC reconfiguration interface will not be separated for each channel.

7. Dynamic Reconfiguration

UG-20056 | 2019.02.04

Intel

®

 Stratix

®

 10 E-Tile Transceiver PHY User Guide

Send Feedback

132

Содержание Stratix 10





































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды