Intel Stratix 10 Скачать руководство пользователя

Страница: 24 / 228

2. Implementing the Transceiver PHY Layer in Intel

Stratix 10 Devices

2.1. Transceiver Design Flow in the Native PHY IP Core

The Intel Stratix 10 E-Tile Native PHY IP core is the primary access point allowing you

to access and customize the Native PHY IP core.

The E-Tile Native PHY IP core supports the following usage modes:
•

PMA Direct

•

PMA Direct high data rate PAM4

•

Gearbox 64/66

•

PLL

Note:

Additional modes will be supported in a future release of the Intel Quartus

Prime Pro

Edition software.

The PMA Direct usage mode is for PMA NRZ and PAM4 usage in the E-Tile Native PHY

IP core. The data is transferred directly between PMA interface and FPGA fabric

through the EMIB. You can place a total of 24 PMA Direct channels in one E-Tile. This

mode is supported for both NRZ and PAM4 with the following PMA interface widths:
•

•

64 (Only in PMA Direct high data rate PAM4 mode)

The E-Tile Native PHY IP core's integrated reset controller provides reset signals for

the PMA Direct and PMA Direct high data rate PAM4 modes.

UG-20056 | 2019.02.04

Send Feedback

and Stratix words and logos are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other

countries. Intel warrants performance of its FPGA and semiconductor products to current specifications in

accordance with Intel's standard warranty, but reserves the right to make changes to any products and services

at any time without notice. Intel assumes no responsibility or liability arising out of the application or use of any

information, product, or service described herein except as expressly agreed to in writing by Intel. Intel

customers are advised to obtain the latest version of device specifications before relying on any published

information and before placing orders for products or services.

*Other names and brands may be claimed as the property of others.

ISO

9001:2015

Registered

Содержание Stratix 10





































































































































































































































Результаты поиска

Содержание Stratix 10

Отзывы:

Похожие инструкции для Stratix 10

Бренды по названию

Популярные бренды

Intel Stratix 10, Руководство пользователя

Результаты поиска

Содержание Stratix 10

Отзывы:

Похожие инструкции для Stratix 10

Бренды по названию

Популярные бренды