Intel ITANIUM ARCHITECTURE Скачать руководство пользователя страница 338 | Manualshive

Страница: 338 / 604

Intel ITANIUM ARCHITECTURE Скачать руководство пользователя страница 338

Volume 4: Base IA-32 Instruction Reference

4:331

RDMSR—Read from Model Specific Register

Description

Loads the contents of a 64-bit model specific register (MSR) specified in the ECX
register into registers EDX:EAX. The EDX register is loaded with the high-order 32 bits
of the MSR and the EAX register is loaded with the low-order 32 bits. If less than 64 bits
are implemented in the MSR being read, the values returned to EDX:EAX in
unimplemented bit locations are undefined.

This instruction must be executed at privilege level 0 or in real-address mode;
otherwise, a general protection exception #GP(0) will be generated. Specifying a
reserved or unimplemented MSR address in ECX will also cause a general protection
exception.

The MSRs control functions for testability, execution tracing, performance-monitoring
and machine check errors.

The CPUID instruction should be used to determine whether MSRs are supported
(EDX[5]=1) before using this instruction.

See model-specific instructions for all the MSRs that can be written to with this
instruction and their addresses

Operation

IF Itanium System Environment THEN IA-32_Intercept(INST,RDMSR);

EDX:EAX



MSR[ECX];

Flags Affected

None.

Additional Itanium System Environment Exceptions

IA-32_Intercept

Mandatory Instruction Intercept.

Protected Mode Exceptions

#GP(0)

If the current privilege level is not 0.
If the value in ECX specifies a reserved or unimplemented MSR

address.

Real Address Mode Exceptions

#GP

If the current privilege level is not 0
If the value in ECX specifies a reserved or unimplemented MSR

address.

Opcode

Instruction

Description

0F 32

RDMSR

Load MSR specified by ECX into EDX:EAX

«
...
336
337
338
339
340
...
»

Содержание ITANIUM ARCHITECTURE





























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды