Intel DB75EN страница 55 Скачать руководство пользователя

Страница: 55 / 96

Technical Reference

2.3

Jumper Block

CAUTION

Do not move the jumper with the power on. Always turn off the power and unplug the

power cord from the computer before changing a jumper setting. Otherwise, the

board could be damaged.
Figure 14 shows the location of the jumper block. The 3-pin jumper block determines

the BIOS Setup program’s mode. Table 30 describes the jumper settings for the three

modes: normal, configure, and recovery. When the jumper is set to configure mode

and the computer is powered-up, the BIOS compares the processor version and the

microcode version in the BIOS and reports if the two match.

Figure 14. Location of the Jumper Block

Table 30. BIOS Setup Configuration Jumper Settings

Function/Mode

Jumper Setting Configuration

Normal

1-2

The BIOS uses current configuration information and passwords
for booting.

Configure

2-3

After the POST runs, Setup runs automatically. The
maintenance menu is displayed.

Note that this Configure mode is the only way to clear the
BIOS/CMOS settings. Press F9 (restore defaults) while in
Configure mode to restore the BIOS/CMOS settings to their
default values.

Recovery

None

The BIOS attempts to recover the BIOS configuration. A
recovery CD or flash drive is required.

Содержание DB75EN

































































































Результаты поиска

Содержание DB75EN

Отзывы:

Похожие инструкции для DB75EN

Бренды по названию

Популярные бренды

Intel DB75EN, Спецификация

Результаты поиска

Содержание DB75EN

Отзывы:

Похожие инструкции для DB75EN

Бренды по названию

Популярные бренды