Intel DB75EN страница 27 Скачать руководство пользователя

Страница: 27 / 96

Product Description

1.9

LAN Subsystem

The LAN subsystem consists of the following:

•

Intel 82579V Gigabit Ethernet Controller (10/100/1000 Mb/s)

•

Intel B75 Express Chipset

•

RJ-45 LAN connector with integrated status LEDs

Additional features of the LAN subsystem include:

•

CSMA/CD protocol engine

•

LAN connect interface between the PCH and the LAN controller

•

Conventional PCI bus power management



ACPI technology support



LAN wake capabilities

•

ACPI technology support

•

LAN wake capabilities

•

LAN subsystem software

For information about

Refer to

LAN software and drivers

http://downloadcenter.intel.com

1.9.1

Intel

82579V Gigabit Ethernet Controller

The Intel 82579V Gigabit Ethernet Controller supports the following features:

•

10/100/1000 BASE-T IEEE 802.3 compliant

•

Energy Efficient Ethernet (EEE) IEEE802.3az support (Low Power Idle [LPI] mode)

•

Dual interconnect between the Integrated LAN Controller and the Physical Layer

(PHY):



PCI Express-based interface for active state operation (S0) state



SMBUS for host and management traffic (Sx low power state)

•

Compliant to IEEE 802.3x flow control support

•

802.1p and 802.1q

•

TCP, IP, and UDP checksum offload (for IPv4 and IPv6)

•

Full device driver compatibility

Содержание DB75EN

































































































Результаты поиска

Содержание DB75EN

Отзывы:

Похожие инструкции для DB75EN

Бренды по названию

Популярные бренды

Intel DB75EN, Спецификация

Результаты поиска

Содержание DB75EN

Отзывы:

Похожие инструкции для DB75EN

Бренды по названию

Популярные бренды