Intel DB75EN Скачать руководство пользователя

Страница: 66 / 96

Intel Desktop Board DB75EN Technical Product Specification

To install an operating system that supports USB, verify that Legacy USB support in

the BIOS Setup program is set to Enabled and follow the operating system’s

installation instructions.

3.6

BIOS Updates

The BIOS can be updated using either of the following utilities, which are available on

the Intel World Wide Web site:

•

Intel

Express BIOS Update utility, which enables automated updating while in the

Windows environment. Using this utility, the BIOS can be updated from a file on a

hard disk, a USB drive (a flash drive or a USB hard drive), or a CD-ROM, or from

the file location on the Web.

•

Intel

Flash Memory Update Utility, which requires booting from DOS. Using this

utility, the BIOS can be updated from a file on a hard disk, a USB drive (a flash

drive or a USB hard drive), or a CD-ROM.

Both utilities verify that the updated BIOS matches the target system to prevent

accidentally installing an incompatible BIOS.

NOTE

Review the instructions distributed with the upgrade utility before attempting a BIOS

update.

For information about

Refer to

BIOS update utilities

http://support.intel.com/support/motherboards/desktop/sb

/CS-022312.htm

3.6.1

Language Support

The BIOS Setup program and help messages are supported in US English. Check the

Intel web site for support.

Содержание DB75EN

































































































Результаты поиска

Содержание DB75EN

Отзывы:

Похожие инструкции для DB75EN

Бренды по названию

Популярные бренды

Intel DB75EN, Спецификация

Результаты поиска

Содержание DB75EN

Отзывы:

Похожие инструкции для DB75EN

Бренды по названию

Популярные бренды