Intel DB75EN Скачать руководство пользователя

Страница: 3 / 96

iii

Board Identification Information

Basic Desktop Board DB75EN Identification Information

AA Revision

BIOS Revision

Notes

G39650-300

ENB7510H.86A.0017

1,2

Notes:
1. The AA number is found on a small label on the component side of the board.
2. The B75 processor used on this AA revision consists of the following component:

Device

Stepping

S-Spec Numbers

Intel B75 Express Chipset

SLJ85

Specification Changes or Clarifications

Table 1 indicates the Specification Changes or Specification Clarifications that apply to

the Intel

Desktop Board DB75EN.

Table 1. Specification Changes or Clarifications

Date

Type of Change

Description of Changes or Clarifications

June 2012

Spec Clarification

Removed references to RAID support and replaced with
SATA ACHI support.

Errata

Current characterized errata, if any, are documented in a separate Specification

Update. See

http://developer.intel.com/products/desktop/motherboard/index.htm

for the latest documentation.

Содержание DB75EN

































































































Результаты поиска

Содержание DB75EN

Отзывы:

Похожие инструкции для DB75EN

Бренды по названию

Популярные бренды

Intel DB75EN, Спецификация

Результаты поиска

Содержание DB75EN

Отзывы:

Похожие инструкции для DB75EN

Бренды по названию

Популярные бренды