Intel DB75EN страница 60 Скачать руководство пользователя

Страница: 60 / 96

Intel Desktop Board DB75EN Technical Product Specification

CAUTION

Ensure that the ambient temperature does not exceed the board’s maximum operating

temperature. Failure to do so could cause components to exceed their maximum case

temperature and malfunction. For information about the maximum operating

temperature, see the environmental specifications in Section 2.9.

CAUTION

Ensure that proper airflow is maintained in the processor voltage regulator circuit.

Failure to do so may result in damage to the voltage regulator circuit. The processor

voltage regulator area (shown in Figure 17) can reach a temperature of up to 120

C in

an open chassis.

Figure 17 shows the locations of the localized high temperature zones.

Item

Description

Processor voltage regulator area

Processor

Intel B75 Express Chipset

Figure 17. Localized High Temperature Zones

Содержание DB75EN

































































































Результаты поиска

Содержание DB75EN

Отзывы:

Похожие инструкции для DB75EN

Бренды по названию

Популярные бренды

Intel DB75EN, Спецификация

Результаты поиска

Содержание DB75EN

Отзывы:

Похожие инструкции для DB75EN

Бренды по названию

Популярные бренды