Intel DB75EN Скачать руководство пользователя

Страница: 63 / 96

Overview of BIOS Features

3.1

Introduction

The board uses an Intel BIOS that is stored in the Serial Peripheral Interface Flash

Memory (SPI Flash) and can be updated using a disk-based program. The SPI Flash

contains the BIOS Setup program, POST, the PCI auto-configuration utility, LAN

EEPROM information, and Plug and Play support.
The BIOS displays a message during POST identifying the type of BIOS and a revision

code. The initial production BIOSs are identified as ENB7510H.86A.
When the BIOS Setup configuration jumper is set to configure mode and the computer

is powered-up, the BIOS compares the CPU version and the microcode version in the

BIOS and reports if the two match.
The BIOS Setup program can be used to view and change the BIOS settings for the

computer. The BIOS Setup program is accessed by pressing the <F2> key after the

Power-On Self-Test (POST) memory test begins and before the operating system boot

begins. The menu bar is shown below.

Maintenance Main Configuration Performance

Security Power

Boot

Exit

NOTE

The maintenance menu is displayed only when the board is in configure mode.

Section 2.3 on page 55 shows how to put the board in configure mode.

Содержание DB75EN

































































































Результаты поиска

Содержание DB75EN

Отзывы:

Похожие инструкции для DB75EN

Бренды по названию

Популярные бренды

Intel DB75EN, Спецификация

Результаты поиска

Содержание DB75EN

Отзывы:

Похожие инструкции для DB75EN

Бренды по названию

Популярные бренды