Intel 80331 Скачать руководство пользователя страница 48

Страница: 48 / 148

Intel® 80331 I/O Processor

Design Guide

PCI-X Layout Guidelines

6.4.2

Single-Slot at 133 MHz

Figure 17

shows one of the chipset PCI AD lines connected through TL_AD1 line segments to a

single-slot connector CONN1 through TL1 line segment to the 80331.

Figure 17.

Single-Slot Point-to-Point Topology

Table 9.

PCI-X 133 MHz Single Slot Routing Recommendations

Parameter

Routing Guideline for Lower AD Bus Routing Guideline for Upper AD Bus

Reference Plane

Preferred Layer

Route over an unbroken ground plane

Stripline

Breakout

5 mils on 5 mils spacing. Maximum length of breakout region is 500 mils.

Motherboard Impedance (for
both microstrip and stripline)

50 ohms +/- 15%

Add-in card Impedance (for
both microstrip and stripline)

57 ohms +/- 15%

Stripline Trace Spacing

12 mils from edge to edge

Microstrip Trace Spacing

18 mils from edge to edge

Group Spacing

Spacing from other groups: 25 mils minimum edge to edge

Trace Length 1 (TL1): From
80331 signal Ball to first
junction

2.25” minimum - 7.5” maximum

1.25” minimum - 6.75” maximum

Trace Length 2 (TL_AD1)-
from connector to receiver

0.75” minimum - 1.5” maximum

1.75” minimum - 2.75” maximum

Length Matching
Requirements:

No length matching is required among datalines. For length matching for clocks,
refer clock guidelines

Table 8

Number of vias

Two vias maximum

TL1

CONN1

AD1

Содержание 80331





















































































































































Результаты поиска

Содержание 80331

Отзывы:

Похожие инструкции для 80331

Бренды по названию

Популярные бренды

Intel 80331, Руководство по конструкции

Результаты поиска

Содержание 80331

Отзывы:

Похожие инструкции для 80331

Бренды по названию

Популярные бренды