manualshive.com logo in svg

Intel 6300ESB ICH, Руководство по конструкции

Intel 6300ESB ICH - Дизайн-руководство для этого продукта доступно для загрузки совершенно бесплатно на manualshive.com. Скачайте нужный вам руководство сейчас, чтобы использовать этот продукт на максимальной производительности.

Поделиться
Скачать
background image

84

 

Intel

®

 855GME Chipset and Intel

®

 6300ESB ICH Embedded Platform Design Guide

4.3.2

Recommended ITP Interposer Debug Port Implementation

Intel is working with American Arium* to provide ITP interposer cards for use in debugging Intel 
Pentium M/Celeron M processor-based systems as an alternative to the onboard ITP700FLEX in 
cases where the onboard connector cannot be supported. The ITP interposer card is an additional 
component that integrates a Intel Pentium M/Celeron M processor socket along with ITP700 
connector on a single interposer card that is compatible with the 478-pin Intel Pentium M/Celeron 
M processor socket. 

Table 7

 summarizes all the signals that require termination for a system designed for use with the 

ITP interposer. This includes TDI, TMS, TRST#, and TCK. TDO may be left as a no connect.

DBR# should be routed to the system reset logic (e.g., the SYSRST# signal of the 6300ESB) and 
initiate the equivalent of a front panel reset commonly found in desktop systems. The 150

Ω

 to 

240

Ω

 pull-up resistor should be placed within 1 ns of the ITP connector. 

Note:

The processor should not be power cycled when DBR# is asserted.

DBA# is an optional system signal that may be used to indicate to the system that the ITP/TAP port 
is being used. When not implemented, this signal may be left as no connect. When implemented, it 
shall be routed with a 150

Ω

 to 240

Ω

 pull-up resistor placed within 1 ns of the ITP connector.

4.3.2.1

ITP_CLK Routing to ITP Interposer 

A layout example for ITP_CLK/ITP_CLK# routing to the CPU socket for supporting an ITP 
interposer is shown in 

Figure 39

. The CK409 clock chip is mounted on the primary side layer of 

the motherboard and the differential clock pair also breaks out on the same side. The differential 
ITP clock pair routing also requires a pair of 33

Ω

± 5 percent series resistors placed within 0.5 

inches of the clock chip output pins and followed by a pair of 49.9

Ω

± 1 percent termination 

resistors to ground. The majority of the ITP_CLK differential serpentine routing takes place on 
internal Layer 6 below the Intel Pentium M/Celeron M processor FSB address signal routing. 

Completion of ITP+CLK routing on Layer 6 is not possible due to Intel Pentium M/Celeron M 
processor FSB routing on Layer 6. Therefore the ITP_CLK differential pair then is routed to the 
secondary side layer to complete routing to the ITP_CLK (pin A16) and ITP_CLK# (pin A15) pins 
of the Intel Pentium M/Celeron M processor while matching the BCLK[1:0] routing on the 
secondary side for a 507 mil length (see 

Figure 16

 and description in 

Section 4.1.7

). Routing to the 

CPU socket on the primary side layer is not possible because of the presence of the VCCA 1.8 V or 
1.5 V plane flood along the A-signal side row of the pin-map. ITP_CLK routing to the ITP 
interposer should achieve the ± 50 ps length matching requirement of the BCLK[1:0] lines.

Содержание 6300ESB ICH

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6300ESB ICH

XDS 910 Reference Manual preview
910
Бренд: XDS Страницы: 99
Dave Embedded Systems ARM Cortex-A9 MPCore Quick Start Manual preview
ARM Cortex-A9 MPCore
Бренд: Dave Embedded Systems Страницы: 67
Roland Super Sound Set SR-JV80-07 Owner'S Manual preview
Super Sound Set SR-JV80-07
Бренд: Roland Страницы: 8
Schrack Technik HSERG245GS Instruction Sheet preview
HSERG245GS
Бренд: Schrack Technik Страницы: 2
NEC Thin Client US310e Getting Started preview
Thin Client US310e
Бренд: NEC Страницы: 6
Mitsubishi 32172 User Manual preview
32172
Бренд: Mitsubishi Страницы: 874
Mellanox Technologies ConnectX 3 Pro User Manual preview
ConnectX 3 Pro
Бренд: Mellanox Technologies Страницы: 57
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Бренд: ADTRAN Страницы: 2
3Com FEM656C Quick Start Manual preview
FEM656C
Бренд: 3Com Страницы: 53
MCT MPU100ZW User Manual preview
MPU100ZW
Бренд: MCT Страницы: 12
Mobatime DTS 4020.timebridge Mounting And Instruction Manual preview
DTS 4020.timebridge
Бренд: Mobatime Страницы: 94
Avocent Cyclades CS4008 Specifications preview
Cyclades CS4008
Бренд: Avocent Страницы: 2
IBM 09N4076 User Manual preview
09N4076
Бренд: IBM Страницы: 78
Siklu EtherHaul 500 Installation Manual preview
EtherHaul 500
Бренд: Siklu Страницы: 52
UltrArmor UA3 Series User Manual preview
UA3 Series
Бренд: UltrArmor Страницы: 3
ubiquoss U9016B Installation Manual preview
U9016B
Бренд: ubiquoss Страницы: 46
Renesas M3T-F160-100NSD User Manual preview
M3T-F160-100NSD
Бренд: Renesas Страницы: 6
Sharp PN-E601 Specifications preview
PN-E601
Бренд: Sharp Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды