manualshive.com logo in svg

Intel 6300ESB ICH, Руководство по конструкции

Intel 6300ESB ICH - Дизайн-руководство для этого продукта доступно для загрузки совершенно бесплатно на manualshive.com. Скачайте нужный вам руководство сейчас, чтобы использовать этот продукт на максимальной производительности.

Поделиться
Скачать
background image

86

 

Intel

®

 855GME Chipset and Intel

®

 6300ESB ICH Embedded Platform Design Guide

4.3.3.1

Mechanical Considerations

The LAI is installed between the processor socket and the Intel Pentium M/Celeron M processor. 
The LAI pins plug into the socket, while the Intel Pentium M/Celeron M processor in the 478-pin 
package plugs into a socket on the LAI. Cabling this part of the LAI egresses the system to allow 
an electrical connection between the Intel Pentium M/Celeron M processor and a logic analyzer. 
The maximum volume occupied by the LAI, known as the keepout volume, as well as the cable 
egress restrictions, should be obtained from the logic analyzer vendor. System designers must 
make sure that the keepout volume remains unobstructed inside the system.

Note:

It is possible that the keepout volume reserved for the LAI may include space normally occupied 
by the Intel Pentium M/Celeron M processor heat sink. When this is the case, the logic analyzer 
vendor shall provide a cooling solution as part of the LAI.

4.3.3.2

Electrical Considerations

The LAI also affects the electrical performance of the Intel Pentium M/Celeron M processor 
system bus. Therefore, it is critical to obtain electrical load models from each of the logic analyzers 
to be able to run system level simulations to prove that their tool works in the system. Contact the 
logic analyzer vendor for electrical specifications as load models for the LAI solution they provide.

4.3.4

Processor Phase Lock Loop (PLL) Design Guidelines

4.3.4.1

Processor PLL Power Delivery

V

CCA

[3:0] is a power source required by the PLL clock generators on the processor silicon. 

Because these PLLs are analog in nature, they require quiet power supplies for minimum jitter. 
Jitter is detrimental to the system because it degrades external I/O timings as well as internal core 
timings (i.e., maximum frequency). Traditionally this supply is low-pass filtered to prevent any 
performance degradation. The Intel Pentium M/Celeron M processor has an internal PLL super 
filter for the 1.8 V supply to the VCCA [3:0] pins that dispenses with the need for any external 
low-pass filtering. However, one 0603 form factor 10 nF and one 1206 form factor 10 µF 
decoupling capacitor should be placed as close as possible to each of the four VCCA pins (i.e., a 
pair of capacitors consisting of one 10 nF and one 10 µF should be used for each VCCA pin). 
VCCA power delivery should meet the 1.8 V ± 5 percent tolerance at the VCCA pins. As a result, 
to meet the current demand of the Intel Pentium M/Celeron M processor and the future Intel 
Pentium M/Celeron M processor family, it is strongly recommended that the VCCA feed resistance 
from the 1.8 V power supply up to the VCCA shorting scheme described below be less than 0.1

Ω

. 

It is recommended that the main VCCA feed be connected to the Intel Pentium M/Celeron M 
processor VCCA1 pin. Refer to 

Section 4.3.4.3

 for Intel Pentium M/Celeron M processor PLL 

decoupling requirements.

Figure 40

 illustrates the recommended layout example of the VCCA[3:0] pins feed and 

decoupling. The 1.8 V flood on Layer 3 from the Intel 855GME chipset is a via routed up to the 
primary side layer with a cluster of five 1.8 V vias and two GND stitching vias as shown on the left 
and middle side of 

Figure 40

. On the primary layer side, a wide flood in a U-shape shorts the four 

VCCA[3:0] pins of the processor. To minimize resistance and inductance of the U-shaped VCCA 
flood shorting the VCCA[3:0] pins, the flood should be at least 100 mils wide and be spaced at 
least 25 mils from any switching signals. When possible, a flood wider than the 100 mil minimum 
shall be implemented and shall reference a ground plane only. Do not reference any switching 
signals or split planes. The recommended wide flood on the primary side benefits from low 

Содержание 6300ESB ICH

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6300ESB ICH

Lattice Semiconductor ECP5 Versa Quick Start Manual preview
ECP5 Versa
Бренд: Lattice Semiconductor Страницы: 15
XESS XStend XS40 User Manual preview
XStend XS40
Бренд: XESS Страницы: 23
Enterasys Enterasys Matrix 2G4082-25 Hardware Installation Manual preview
Enterasys Matrix 2G4082-25
Бренд: Enterasys Страницы: 58
C&T Solution VCO-6131E-4M2 User Manual preview
VCO-6131E-4M2
Бренд: C&T Solution Страницы: 129
TRENDnet TEW-641PC Quick Installation Manual preview
TEW-641PC
Бренд: TRENDnet Страницы: 12
Radio Shack Bluespoon 17-1000 Quick Start Manual preview
Bluespoon 17-1000
Бренд: Radio Shack Страницы: 1
JETWAY I848ASR1A User Manual preview
I848ASR1A
Бренд: JETWAY Страницы: 47
Laser UDC CARD User Manual preview
UDC CARD
Бренд: Laser Страницы: 4
Kaya Instruments KY-FGK Reference Manual preview
KY-FGK
Бренд: Kaya Instruments Страницы: 48
Cooler Master Masterliquid ML240L RGB Manual preview
Masterliquid ML240L RGB
Бренд: Cooler Master Страницы: 18
Net Optics Phantom HD Quick Install Manual preview
Phantom HD
Бренд: Net Optics Страницы: 2
Freescale Semiconductor KW2xD Series Reference Manual preview
KW2xD Series
Бренд: Freescale Semiconductor Страницы: 42
One Identity Safeguard for Privileged Sessions 3000 Installation Manual preview
Safeguard for Privileged Sessions 3000
Бренд: One Identity Страницы: 37
Variscite VAR-SOM-MX6 HEAT PLATE KIT Quick Start Manual preview
VAR-SOM-MX6 HEAT PLATE KIT
Бренд: Variscite Страницы: 3
FDI USB-ICP-SAB9 Quick Start Manual preview
USB-ICP-SAB9
Бренд: FDI Страницы: 15
Bdcom GP3600-16 Hardware Installation Manual preview
GP3600-16
Бренд: Bdcom Страницы: 25
ekwb SLIM 120 User Manual preview
SLIM 120
Бренд: ekwb Страницы: 36
Olivella Modular Signos User Manual preview
Signos
Бренд: Olivella Modular Страницы: 19

Бренды по названию

Популярные бренды

Загрузить еще бренды