Advanced Operations
En-72
Adjusting the Volume for Zones
■
Operating on the remote controller
■
Operating on the AV receiver
If your Zone 2/3 speakers are connected to a receiver or
integrated amplifier in Zone 2/3, use its volume control to
adjust the volume.
Muting Zones
■
Operating on the remote controller
Tip
• To unmute, press
Zone2
or
Zone3
followed by
Muting
again.
Zones can also be unmuted by adjusting the volume.
Adjusting the Tone and Balance of Zone 2
Note
• Only analog input sources are output by the
ZONE 2/3
PRE/LINE OUT
,
FRONT WIDE/ZONE 2 L/R
and
FRONT
HIGH/ZONE 3 L/R
terminals. Digital input sources are not
output. If no sound is heard when an input source is selected,
verify that the source is connected to an analog input.
• You cannot select different AM or FM radio stations for your
main room and Zone 2/3. The same AM/FM radio station will be
heard in each room. Namely, if you have selected an FM station
for the main room, that station will also be output in Zone 2/3.
• When you have selected
NET
or
USB
as input selector, the last
selector selected will be set for Main room and Zone 2/3.
• When Zone 2/3 is activated and its input selector is selected, the
power consumption of standby mode slightly increases.
• While Zone 2/3 is on,
u
functions will not work.
• When setting the AV receiver to standby mode while Zone 2/3 is
active, the
Z2
or
Z3
indicator is dimly lit.
• The Zone 2 level, balance, and tone functions have no effect on
the
ZONE 2 PRE/LINE OUT
jacks when the “
Zone 2 Out
”
setting is set to “
Fixed
” (
➔
page 66
).
• The Zone 3 volume function has no effect on
ZONE 3
PRE/LINE OUT
when the “
Zone 3 Out
” setting is set to
“
Fixed
” (
➔
page 66
).
The 12V triggers A, B, and C can be used to turn on 12V
trigger-capable components automatically when they are
selected as the input source. The triggers can be set so that
they activate themselves once a connected component is
selected as the input source for the main room, Zone 2,
Zone 3, or any combination of rooms. When triggered, the
output from a
12V TRIGGER OUT
goes high (+12 volts
and 150 milliamperes max. at
12V TRIGGER OUT A
;
+12 volts and 25 milliamperes max. at
12V TRIGGER
OUT B
and
C
).
See “12V Trigger A/B/C Setup” (
➔
page 65
).
Hookup
• Use a miniplug cable to connect the AV receiver’s
12V
TRIGGER OUT A
,
B
, or
C
jack to the 12 V trigger
input of a connected component.
1
Press
Zone2
or
Zone3
.
2
Use
VOL
q
/
w
.
1
Press
Zone 2
or
Zone 3
(the Z2/Z3 indicator on the
display flashes).
2
Use
Master Volume
control within 8 seconds.
1
Press
Zone2
or
Zone3
, and then press
Muting
.
1
On the AV receiver, press
Zone 2
.
2
Press the AV receiver’s
Tone
repeatedly to select
“Bass”, “Treble” or “Balance”.
3
Use
–
or
+
to adjust the bass, treble or balance.
• You can boost or cut the bass or treble from –10 dB
to +10 dB in 2 dB steps.
• You can adjust the balance from 0 in the center to
+10 dB to the right or +10 dB to the left in 2 dB
steps.
Using the 12V Triggers
Содержание DTR-40.4
Страница 1: ...AV Receiver DTR 40 4 Instruction Manual ...
Страница 102: ...Appendix En 102 Memo ...
Страница 103: ...Appendix En 103 Memo ...