Integra DTR-40.4, Инструкция по эксплуатации

Страница: 54 / 104

Advanced Operations
En-54
Digital Audio Input
If you connect a component to a digital audio input, you
must assign that input to an input selector. For example, if
you connect your CD player to the
OPTICAL IN 1
, you
must assign “ OPTICAL1 ” to the “ TV/CD ” input selector.
Here are the default assignments.
■
BD/DVD , CBL/SAT , STB/DVR, GAME , PC , AUX,
TV/CD , PHONO
`
COAXIAL1 , COAXIAL2 , COAXIAL3 ,
OPTICAL1 , OPTICAL2 :
Select the input to which the component has been
connected.
`
- - - - - :
Select if the component is connected to an analog
audio input.
Note
• When an
HDMI IN
is assigned to an input selector in
“ HDMI Input ” (
➔
page 52
), the same
HDMI IN
will be set as
a priority in this assignment. In this case, if you want to use the
coaxial or optical audio input, make the appropriate selection in
the “
Audio Selector ” (
➔
page 63 ).
• Supported sampling rates for PCM signals (stereo/mono) from a
digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16,
20, 24 bit.
Main Menu Speaker Setup
Here you can check the settings made by Audyssey 2EQ
Room Correction and Speaker Setup function, or set them
manually, which is useful if you change one of the
connected speakers after using Audyssey 2EQ Room
Correction and Speaker Setup function.
Note
• These settings are not available in either of the following cases:
– a pair of headphones is connected.
– the “
Audio TV Out ” setting is set to “ On ” (
➔
page 67 ).
– “ HDMI Control(RIHD) ” is set to “ On ” (
➔
page 66 ) and
you’re listening through your TV speakers.
Speaker Settings
If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
If you bi-amp the front speakers, you must change the
“
Speakers Type(Front) ” setting. For details on speaker
wire connection, see “Bi-amping the Front Speakers”
(
➔
page 13
).
Note
• When bi-amping is used, the AV receiver is able to drive up to 5.1
speakers in the main room.
• Before you change these settings, turn down the volume.
■
Speaker Impedance
`
4ohms :
Select if the impedance of any speaker is 4 ohms or
more but less than 6.
`
6ohms :
Select if the impedances of all speakers are between 6
and 16 ohms.
■
Speakers Type(Front)
`
Normal :
Select this if you’ve connected your front speakers
normally.
`
Bi-Amp :
Select this if you’ve bi-amped your front speakers.
■
Powered Zone 2, Powered Zone 3
`
No
`
Yes :
Zone 2/3 speakers can be used. (Powered Zone 2/3
enabled).
Note
• If the “ Speakers Type(Front) ” setting is set to “ Bi-Amp ”,
Powered Zone 2/3 cannot be used.
• When the “ Powered Zone 2 ” setting is set to “ Yes ” and Zone 2
is turned on, the surround back and front high speakers cannot be
used.
• If the “ Powered Zone 2 ” setting is set to “ No ”, the “ Powered
Zone 3 ” setting cannot be selected.
Input selector Default assignment
BD/DVD COAXIAL1
CBL/SAT COAXIAL2
STB/DVR COAXIAL3
GAME OPTICAL1
PC - - - - -
AUX - - - - -
TV/CD OPTICAL2
PHONO - - - - -
Speaker Setup
Some of the settings in this section are set automatically
by Audyssey 2EQ
® Room Correction and Speaker Setup
(
➔
page 34
).
If you change these settings, you must run
Audyssey 2EQ Room Correction and Speaker Setup
again (
➔
page 34 ).
1 2 3 4 5
“ Setup ”