Inova SV 125 Скачать руководство пользователя страница 77

Страница: 77 / 392

SV 125
4016589

Structure and function

Version 1.0

4--17

4.2.12.1

Sensors of the stopper insertion station

Sensor

Stopper upside down in stopper turning device

(Z) checks, if the stop-

pers are correctly orientated.

If a stopper is not correctly positioned, the stopper pin presses it into the stopper

turning device too far. As soon as the sensor detects a stopper, the machine stops.

The respective stopper must be removed manually.

Sensor

Insertion tube overload

(AA) checks, if an insertion tube has changed its

position in the holder. As soon as the sensor detects an insertion tube, the machine

stops. After the cause of the fault has been eliminated, the respective insertion tube

must be positioned correctly by hand.

Sensor

Stopper inserted

(AB) checks, if stoppers have been inserted in the syr-

inges. Through the stoppers that have been inserted, the stopper insertion rod is

pressed up. If no stopper has been inserted, the stopper insertion rod remains in

position and this fact is detected by the sensor.

The machine stops, if a presettable number of stoppers are missing in sequence

(consecutive fault).

Nests that have not been correctly processed can either be processed further or

can be discharged ahead of schedule.

Syringes that have not been closed must be taken out of the nest manually after

the processing has ended.

Содержание SV 125









































































































































































































































































































































































































Результаты поиска

Содержание SV 125

Отзывы:

Бренды по названию

Популярные бренды

Inova SV 125, Руководство по эксплуатации

Результаты поиска

Содержание SV 125

Отзывы:

Бренды по названию

Популярные бренды