Inova SV 125 Скачать руководство пользователя страница 182

Страница: 182 / 392

Operation

SV 125

4016589

5--96

Version 1.0

On the teach--in screen for the needle stroke the needle is moved to the step points.

On the Format input screen the detected values are entered.

NOTE

Watch travel movement of axis to avoid collision.

Mode of procedure

Select input field “Start dosage position” on screen 691 and enter the value
for the filling start (in this example 190

Touch input field ”No. of step points” and enter the desired number of step
points (in this example 3).

Call up screen

Format input -- Teach servo axis needle stroke

and touch

control field

to move the filling needle to the lowest position in the syr-

inge. Note down the value.

Touch control field

. The dosing is performed in steps. Touch control

field

and move the needle to the first step point. We recommend to

move the filling needle approx. 2mm above fill level. Note down the value. For

the two remaining step points touch control field

and touch control

field

to move the axis to the step points. Note down the values.

To end the process move the filling needle out of the syringe to its upper posi-
tion above the syringe. Note down the value.

Содержание SV 125









































































































































































































































































































































































































Результаты поиска

Содержание SV 125

Отзывы:

Бренды по названию

Популярные бренды

Inova SV 125, Руководство по эксплуатации

Результаты поиска

Содержание SV 125

Отзывы:

Бренды по названию

Популярные бренды