Inova SV 125 Скачать руководство пользователя страница 184

Страница: 184 / 392

Operation

SV 125

4016589

5--98

Version 1.0

5.2.47

Format input -- Filling curve vacuum (piston pumps) [3/4]

Touch control field

on screen

Format input -- Filling curve vacuum (pis-

ton pumps) [2/4]

The parameters for the needle stroke during vacuum filling can be entered.

Needle stroke:

Evacuate position [mm]

Entry of the filling needle position in downward movement, where the vacuum valve

is switched on.

Delay start shaking [ms]

Delay for the shaking of the filling needle.

Position vacuum off [mm]

Entry of the position where the vacuum is switched off. The position is on the up-

ward movement of the filling needle.

Shake -- Upper position [mm]

Upper position for shaking the filling needle.

Содержание SV 125









































































































































































































































































































































































































Результаты поиска

Содержание SV 125

Отзывы:

Бренды по названию

Популярные бренды

Inova SV 125, Руководство по эксплуатации

Результаты поиска

Содержание SV 125

Отзывы:

Бренды по названию

Популярные бренды