Inova SV 125 Скачать руководство пользователя страница 32

Страница: 32 / 392

Safety regulations

SV 125

4016589

1--12

Version 1.0

Immediately report and eliminate any detected fault or damage. Interrupt the

production until the problem has been eliminated.

In case of maintenance or repair work use suitable measures to prevent

others approaching the work area (chain locks and danger signs).

The operating personnel are not allowed to wear their long hair down, to wear

loose--fitting clothes or jewelry.

WARNING!

Fatigue and noise can lead to stressful situations at the work place.

This causes an increased risk of accidents.

Only operate the machine with sound protection. Observe the pre-

scribed breaks and use them for recreation.

1.4.2

First aid

Observe the local safety instructions for first aid.

Observe information relating to available facilities like Emergency phone or first aid

kit.

1.4.2.1

Accident report

Immediately inform supervisors and OPTIMA GROUP pharma about accidents

and hazard sources. If you rapidly inform about hazard sources, their causes can

be immediately eliminated.

1.4.3

Fire prevention

Observe the local safety instructions for fire fighting.

For glowing fires (paper, wood, plastics) only use fire extinguishers class ABC.

For electric fires and fires in the control cabinet a CO

--fire extinguisher must be

used.

Observe information relating to the location and the operation of fire extinguishers.

Содержание SV 125









































































































































































































































































































































































































Результаты поиска

Содержание SV 125

Отзывы:

Бренды по названию

Популярные бренды

Inova SV 125, Руководство по эксплуатации

Результаты поиска

Содержание SV 125

Отзывы:

Бренды по названию

Популярные бренды