Inova SV 125 Скачать руководство пользователя страница 101

Страница: 101 / 392

SV 125
4016589

Operation

Version 1.0

5--15

Reset alarm status

Screen

Alarm -- Status list

is reset.

Reset alarm history

Screen

Alarm -- History

is reset.

Set date/time

Date and time can be set.

Print screen

Screens can be printed.

Performance store

The values of the performance setting can be copied into a format.

Changing the assignment of a function

Touch the input field next to the function whose assignment should be
changed.

With “all users” the function can be assigned to all user groups. The function

is assigned to a certain user group by touching the input field again. After user

level

, the user levels start again from ”all users”.

Repeat the step for all functions that should be changed.

Control field

Function

Screen

Security -- Code [help]

is called up.

The machine drive is switched off.

The previous screen is called up.

Screen

Security -- Code function [2/2]

is called up.

Содержание SV 125









































































































































































































































































































































































































Результаты поиска

Содержание SV 125

Отзывы:

Бренды по названию

Популярные бренды

Inova SV 125, Руководство по эксплуатации

Результаты поиска

Содержание SV 125

Отзывы:

Бренды по названию

Популярные бренды