Inova SV 125 Скачать руководство пользователя страница 46

Страница: 46 / 392

Transport, installation and connection

SV 125

4016589

2--4

Version 1.0

2.4

Installation and connection

DANGER!

Electric shocks can cause severe burns and life--threatening injuries.

Risk of fatal injury from electrical current and other energies.

Only qualified personnel are allowed to connect the machine.

CAUTION!

The danger areas in the transfer areas and on the machine have to be

safeguarded by the plant operator.

NOTE

Due to electromagnetic compatibility (EMC) the machine is only al-

lowed to be operated within the industrial sector.

Adjust the transfer height to the machines connected to this installation.

Place a level device on several places of the base mounting and the sub-
frame of the machine.

Align the machine horizontally by adjusting the spindle feet.

Make sure the weight of the machine is evenly distributed over all spindle feet.

Check the stability of the machine at regular intervals.

Mount the parts and components which were removed for shipping.

Make the electrical connections between the machine and the control cabinet.

Содержание SV 125









































































































































































































































































































































































































Результаты поиска

Содержание SV 125

Отзывы:

Бренды по названию

Популярные бренды

Inova SV 125, Руководство по эксплуатации

Результаты поиска

Содержание SV 125

Отзывы:

Бренды по названию

Популярные бренды