Inova SV 125 Скачать руководство пользователя страница 19

Страница: 19 / 392

SV 125
4016589

Notes

Version 1.0

Page 3

Explanation of terms

Term

Explanation

Safety

devices

Devices that indirectly protect from danger areas (e.g. light grids,

door contact switches).

Protection

devices

Devices that protect from intervention into the danger areas (e.g.

guard doors, casings).

Protective

measures

Measures that must be applied for the protection of persons,

equipment or environment.

Machine

In this operating manual the term machine is identical with plant

(several machines/stations that are combined to one function unit).

Plant operator

Liable person or organisation responsible for machine operation.

Operator,

operating

personnel

Persons who operate the machine or perform operations on the

machine.

Manufacturer

Liable person or organisation responsible for the manufacture of

the machine.

Supplier

Liable person or organisation selling or distributing the machine or

placing it on the market.

Intended use

Permissible application area or permissible use of the machine.

Содержание SV 125









































































































































































































































































































































































































Результаты поиска

Содержание SV 125

Отзывы:

Бренды по названию

Популярные бренды

Inova SV 125, Руководство по эксплуатации

Результаты поиска

Содержание SV 125

Отзывы:

Бренды по названию

Популярные бренды