INIM SmartLoop Series, Руководство по установке

Страница: 13 / 60

Installation manual
General information 13
Figure 4 - CE Mark
2.13 Warranty
INIM Electronics s.r.l. warrants the original purchaser that for a period of 24 months from the date of final
acceptance, the product shall be free of defects in materials and workmanship. The warranty applies only
to defects in parts and workmanship relating to normal use. It does not cover:
Improper use or negligence
Damage caused by fire, flood, wind or lightning
Vandalism
Fair wear and tear
INIM Electronics s.r.l. shall, at its option, repair or replace any defective products. Improper use, that is,
use for purposes other than those mentioned in this manual will void the warranty. For the full details and
conditions regarding the warranty, refer to the purchase order.
2.14 Safety laws
The aim of the instructions in this section is to ensure that the device is installed and handled properly. This
chapter contains vital information. The installer should be familiar with this section and bring each item to
the attention of the system users.
2.14.1 Compliancy
The design and manufacture of the SmartLoop panel comply with EN 54-2 Fire detection and signaling
systems - Control and signaling panels .
The design and manufacture of the power supply comply with EN 54-2 Fire detection and signaling systems
- Power supply devices .
2.14.2 Managing electronic devices
The normal motions of any person may generate electrostatic potential of thousands of volts. Discharge of
this current through semiconductor devices during handling may cause serious damage which although
may not be immediately evident may reduce the reliability of the circuits.
If located in their housings, the electronic circuits of INIM Electronics products are highly immune to
electrostatic discharge.
Do not expose the circuits to damage by removing the modules unnecessarily from their housings.
0051
09
0051 - CPD - 0226
Control and signalling system with integrated
power-supply device.
SmartLOOP/2080-G
EN 54-2:1997+A1:2006
EN 54-4:1997+A1:2002+A2:2006
Isolation: Class I
Options with requirements:
- 7.8 Sounder circuits output
- 7.11 Delayed outputs
- 7.12 Alarm on two points activation
- 8.3 Fault from points signal
- 8.9 Monitored output for remote signalling
- 9.5 Points isolation
- 10.0 Test condition
Manufacturer: INIM Electronics s.r.l.
Address: via Fosso Antico, Centobuchi
63076, Monteprandone (AP), Italy
0051
09
0051 - CPD - 0225
Control and signalling system with integrated
power-supply device.
SmartLOOP/2080-S
EN 54-2:1997+A1:2006
EN 54-4:1997+A1:2002+A2:2006
Isolation: Class I
Options with requirements:
- 7.8 Sounder circuits output
- 7.11 Delayed outputs
- 7.12 Alarm on two points activation
- 8.3 Fault from points signal
- 8.9 Monitored output for remote signalling
- 9.5 Points isolation
- 10.0 Test condition
Manufacturer: INIM Electronics s.r.l.
Address: via Fosso Antico, Centobuchi
63076, Monteprandone (AP), Italy
0051
09
0051 - CPD - 0228
Control and signalling system with integrated
power-supply device.
SmartLOOP/1010-S
EN54-4: 1997/ A2: 2006
EN54-4: 1997/ A1: 2006
Isolation: Class I
Options with requirements:
- 7.8 Sounder circuits output
- 7.11 Delayed outputs
- 7.12 Alarm on two points activation
- 8.3 Fault from points signal
- 8.9 Monitored output for remote signalling
- 9.5 Points isolation
- 10.0 Test condition
Manufacturer: INIM Electronics s.r.l.
Address: via Fosso Antico, Centobuchi
63076, Monteprandone (AP), Italy
0051
09
0051 - CPD - 0227
Control and signalling system with integrated
power-supply device.
SmartLOOP/2080-P
EN 54-2:1997+A1:2006
EN 54-4:1997+A1:2002+A2:2006
Isolation: Class I
Options with requirements:
- 7.8 Sounder circuits output
- 7.11 Delayed outputs
- 7.12 Alarm on two points activation
- 8.3 Fault from points signal
- 8.9 Monitored output for remote signalling
- 9.5 Points isolation
- 10.0 Test condition
Manufacturer: INIM Electronics s.r.l.
Address: via Fosso Antico, Centobuchi
63076, Monteprandone (AP), Italy