Ingersoll-Rand MHP825WCAT Скачать руководство пользователя

Страница: 93 / 109

Fault Finding

Operation & Maintenance Manual

Engine starts
but will not
run or engine
shuts down
prematurely.

Electrical fault

Test the electrical circuits.

Low engine oil pressure.

Check the oil level and oil filter(s).

Safety shut-down system
in operation.

Check the safety shut-down switches.

Fuel starvation.

Check the fuel level and fuel system
components. Replace the fuel filter if
necessary.

Switch failure.

Test the switches.

High compressor oil
temperature.

Check the compressor oil level and oil
cooler. Check the fan drive.

Water present in fuel
system.

Check the water separator and clean if
required.

Faulty relay.

Check the relay in the holder and replace if
necessary.

Engine
Overheats.

Low water level.

Check the level and replenish if necessary.

Blocked radiator.

Stop the machine and clean the cooling
fins with compressed air or steam. Use
reduced pressure for cleaning the fins.

Reduced cooling air from
fan.

Check the fan and the drive belts. Check
for any obstruction inside the cowl.

Faulty thermostat.

Check the thermostat and replace if
necessary.

Engine speed
too low.

Blocked fuel filter.

Check and replace if necessary.

Blocked air filter.

Check and replace the element if
necessary.

Faulty regulator valve.

Check the regulation system.

Premature unloading.

Check the regulation and the operation of
the air cylinder.

Excessive
vibration.

Engine speed too low.

See

“Engine speed too low”

Leaking oil
seal.

Improperly fitted oil seal.

Replace the oil seal.

FAULT

CAUSE

REMEDY

Содержание MHP825WCAT














































































































Результаты поиска

Содержание MHP825WCAT

Отзывы:

Похожие инструкции для MHP825WCAT

Бренды по названию

Популярные бренды

Ingersoll-Rand MHP825WCAT, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание MHP825WCAT

Отзывы:

Похожие инструкции для MHP825WCAT

Бренды по названию

Популярные бренды