Ingersoll-Rand MHP825WCAT Скачать руководство пользователя | Manualshive

Страница: 66 / 109

background image

Operation & Maintenance Manual

Maintenance

64

Inspection

Examine the filter element.

CAUTION

!

If there is any indication of the formation of varnishes, shellacs or
lacquers on the filter element, it is a warning that the compressor
lubricating and cooling oil has deteriorated and that it should be changed
immediately. Refer to LUBRICATION later in this section.

Reassembly

Clean the filter gasket contact area and install the new element by screwing in a clockwise
direction until the gasket makes contact with the filter housing. Tighten a further 1/2 to 3/4 of
a revolution.

CAUTION

!

Start the machine (refer to PRIOR TO STARTING and STARTING THE
UNIT in the OPERATING INSTRUCTIONS section of this manual) and
check for leakage before the machine is put back into service.

Compressor Oil Separator Element

Refer to the

SERVICE MAINTENANCE INTERVAL CHART

in this section for service

intervals.

Removal

WARNING

!

Do not remove the filter(s) without first making sure that the machine is
stopped and the system has been completely relieved of all air pressure.
(Refer to STOPPING THE UNIT in the OPERATING INSTRUCTIONS
section of this manual).

Disconnect all hoses and tubes from the separator tank cover plate. Remove the drop–tube
from the separator tank cover plate and then remove the cover plate. Remove the separator
element.

«
...
64
65
66
67
68
...
»

Содержание MHP825WCAT














































































































Отзывы:

Нет отзывов

Похожие инструкции для MHP825WCAT

Бренд: KAESER KOMPRESSOREN Страницы: 280

Бренд: EasyPro Страницы: 2

Бренд: ABAC Страницы: 91

TU-FLO 700 COMPRESSOR

Бренд: BENDIX Страницы: 36

Бренд: Draper Страницы: 22

AC-B 100/3MC HD

Бренд: F.F. Group Страницы: 72

HGX34/130-4 ML CO2 T

Бренд: GEA Страницы: 46

Бренд: Mangar Health Страницы: 16

Бренд: Parkside Страницы: 88

Бренд: ULTIMATE SPEED Страницы: 122

Бренд: Brooks Страницы: 56

Sabroe SAB 193 L

Бренд: Johnson Controls Страницы: 171

Бренд: Atmos Страницы: 57

Бренд: WilTec Страницы: 8

Бренд: WilTec Страницы: 9

Бренд: WilTec Страницы: 10

Бренд: WilTec Страницы: 12

Бренд: Danfoss Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды