Ingersoll-Rand MHP825WCAT Скачать руководство пользователя страница 95

Страница: 95 / 109

Fault Finding

Operation & Maintenance Manual

Loose pipe/hose
connections.

Check all pipe/hose connections.

Faulty safety valve.

Check the relieving pressure. Replace the
safety valve if faulty.

DO NOT ATTEMPT A

REPAIR.

Oil is forced
back into the
air filter.

Incorrect stopping
procedure used

Always employ the correct stopping procedure.
Close the discharge valve and allow the
machine to run on idle before stopping.

Faulty inlet valve.

Check for free operation of the inlet valve(s).

Machine goes
to full
pressure
when started.

Inlet valve set
incorrectly.
(17/235, 21/215)

Refer to

SPEED AND PRESSURE

REGULATION ADJUSTMENT

in the

MAINTENANCE

section of this manual.

(17/235, 21/215)

Faulty load valve.

Replace the valve.

Machine fails
to load when
the load
button is
pressed.

Faulty load valve.

Replace the valve.

Refer also to the Engine Manufacturer’s Manual.

FAULT

CAUSE

REMEDY

Содержание MHP825WCAT














































































































Результаты поиска

Содержание MHP825WCAT

Отзывы:

Бренды по названию

Популярные бренды

Ingersoll-Rand MHP825WCAT, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание MHP825WCAT

Отзывы:

Бренды по названию

Популярные бренды