Ingersoll-Rand MHP825WCAT страница 72 Скачать руководство пользователя | Manualshive

Страница: 72 / 109

background image

Operation & Maintenance Manual

Maintenance

70

Engine Lubricating Oil

The engine oil should be changed at the engine manufacturer’s recommended intervals. Refer
to the

SERVICE/MAINTENANCE CHART

.

Engine Lubricating Oil Specification

Refer to the

Engine Manufacturer’s Manual or Portable Compressor Fluid Chart.

Engine Oil Filter Element

The engine oil filter element should be changed at the engine manufacturer’s recommended
intervals. Refer to the

SERVICE/MAINTENANCE CHART..

Compressor Lubricating Oil

Refer to the

SERVICE/MAINTENANCE CHART

in this section for service intervals.

NOTE: If the machine has been operating under adverse conditions, or
has suffered long shutdown periods, then more frequent service intervals
will be required.

WARNING

!

DO NOT, under any circumstances, remove any drain plugs or the oil filler
plug from the compressor lubricating and cooling system without first
making sure that the machine is stopped and the system has been
completely relieved of all air pressure (refer to STOPPING THE UNIT in the
OPERATING INSTRUCTIONS section of this manual).

Completely drain the receiver/separator system including the piping and oil cooler by removing
the drain plug(s) and collecting the used oil in a suitable container.

Replace the drain plug(s) ensuring that each one is secure.

NOTE: If the oil is drained immediately after the machine has been
running, then most of the sediment will be in suspension and will
therefore drain more readily.

«
...
70
71
72
73
74
...
»

Содержание MHP825WCAT














































































































Отзывы:

Нет отзывов

Похожие инструкции для MHP825WCAT

Бренд: Unicla Страницы: 14

Бренд: Clarke Страницы: 20

Бренд: Wagan Страницы: 5

Бренд: Gardner Denver Страницы: 58

Бренд: Hamron Страницы: 12

Бренд: Quincy Compressor Страницы: 134

Бренд: Kobalt Страницы: 8

Бренд: Kobalt Страницы: 8

Бренд: Jet Страницы: 22

Бренд: Chicago Pneumatic Страницы: 67

Maneurop VTZ Series

Бренд: Danfoss Страницы: 8

Бренд: GEA Страницы: 26

Бренд: Atlas Copco Страницы: 32

Бренд: Atlas Copco Страницы: 48

XAS 185 KD7 IT4

Бренд: Atlas Copco Страницы: 42

XAS 185 KDU T4F HOP

Бренд: Atlas Copco Страницы: 62

Бренд: EINHELL Страницы: 44

Бренд: EarthLinked Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды