Ingersoll-Rand MHP825WCAT страница 75 Скачать руководство пользователя

Страница: 75 / 109

Maintenance

Operation & Maintenance Manual

Speed and Pressure Regulation Adjustment

Normally, regulation requires no adjusting, but if correct adjustment is lost, proceed as follows:

Refer to the diagram above.

Adjusting screw

Start the machine (Refer to

STARTING INSTRUCTIONS

in the

OPERATING

INSTRUCTIONS

section of this manual).

Adjust the service valve on the outside of the machine to maintain normal operating discharge
pressure (refer to

GENERAL INFORMATION

) and full speed position. If the tachometer

moves away from the full speed position before normal operating discharge pressure is
attained, then turn the adjusting screw ‘

’ clockwise to increase the pressure. Optimum

adjustment is achieved when the throttle just moves from its full speed position and the
pressure increases slightly.

Close the service valve. The engine will slow to idle speed.

CAUTION

Never allow the idle pressure to exceed maximum allowable
pressure(refer to GENERAL INFORMATION).

Содержание MHP825WCAT














































































































Результаты поиска

Содержание MHP825WCAT

Отзывы:

Похожие инструкции для MHP825WCAT

Бренды по названию

Популярные бренды

Ingersoll-Rand MHP825WCAT, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание MHP825WCAT

Отзывы:

Похожие инструкции для MHP825WCAT

Бренды по названию

Популярные бренды