Ingersoll-Rand MHP825WCAT страница 55 Скачать руководство пользователя

Страница: 55 / 109

Operating Instructions

Operation & Maintenance Manual

CAUTION

Never allow the machine to stand idle with pressure in the system.

Emergency Stopping

In the event that the unit has to be stopped in an emergency,

PRESS THE EMERGENCY

STOP SWITCH ON THE FRONT OF THE MACHINE.

If the unit is not fitted with an emergency stop switch, rotate the start switch to the (0) off
position.

Re–Starting After an Emergency

Disengage emergency stop control from engaged (depressed) position. (IF FITTED)

If the machine has been switched off because of a machine malfunction, then identify and
correct the fault before attempting to re–start.

If the machine has been switched off for reasons of safety, then ensure that the machine can
be operated safely before re–starting.

Refer to the

PRIOR TO STARTING

and

STARTING THE UNIT

instructions earlier in this

section before re–starting the machine.

Monitoring During Operation

Should any of the safety shut-down conditions occur, the unit will stop.

Refer to the wedge diagnostic display codes table for a listing of shutdown conditions.

CAUTION

CAUTION: To ensure an adequate flow of oil to the compressor at low
temperature, never allow the discharge pressure to fall below 3.5 bar.

Содержание MHP825WCAT














































































































Результаты поиска

Содержание MHP825WCAT

Отзывы:

Похожие инструкции для MHP825WCAT

Бренды по названию

Популярные бренды

Ingersoll-Rand MHP825WCAT, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание MHP825WCAT

Отзывы:

Похожие инструкции для MHP825WCAT

Бренды по названию

Популярные бренды