Ingersoll-Rand HP1300WCU Скачать руководство пользователя страница 48

Страница: 48 / 75

( )

Book 54757919 (5/02)

Excessive Vibration:

Rubber Mounts, Loose or Damaged

Defective Fan

Drive Coupling Defective

Engine Malfunctioning

Airend Malfunctioning

Engine idle speed too low.

Low CFM:

Dirty Air Filter

Incorrect Linkage Adjustment

Malfunctioning Inlet Unloader/Butterfly Valve

Wrong Air Filter Element

Clean or replace elements.

Make adjustment per Section 6.

Inspect valve. Make adjustment per Section 6.

Install correct element.

Tighten or replace.

Replace fan.

Replace coupling.

See Trouble Shooting in Engine Manual.

See Complaint 15 and 17.

See Engine Manual.

Short Air Cleaner Life:

Dirty Operating Conditions

Inadequate Element Cleaning

Incorrect Stopping Procedure

Wrong Air Filter Element

Will Not Unload:

Malfunctioning Inlet Butterfly Valve

Ice in Regulation Lines/Orifice

Load Solenoid Leak

Plugged Vent Leak

Safety Valve Relieves:

Operating Pressure Too High

Malfunctioning Inlet Unloader/Butterfly Valve

Defective Safety Valve

Unit Will Not Unload Fast Enough

Move unit to cleaner environment.

Install new element.

Read procedure in this manual.

Install proper element.

Inspect valve fit. Re--adjust per Section 6.

Apply heat to line(s) and or orifice.

Replace load solenoid.

Clean and/or replace.

Reduce pressure to spec limit.

Inspect valve fit. Readjust per Section 6.

Replace safety valve.

Apply heat to lines and/or orifice.

10.

11.

12.

Corrective Action

Содержание HP1300WCU












































































Результаты поиска

Содержание HP1300WCU

Отзывы:

Похожие инструкции для HP1300WCU

Бренды по названию

Популярные бренды

Ingersoll-Rand HP1300WCU, Руководство по эксплуатации, техническому обслуживанию и каталог запасных частей

Результаты поиска

Содержание HP1300WCU

Отзывы:

Похожие инструкции для HP1300WCU

Бренды по названию

Популярные бренды