Infranor Xtracontrol DC2 Скачать руководство пользователя

Страница: 57 / 87

User Manual V1.3 | XtracontrolDC2, XtracontrolET2, XtracontrolEC21

The web configuration page will be displayed.

Fig. 43: list of web interface settings

Click on the “Network” link.

The “Network Configuration” page is displayed.

Fig. 44: “Network Configuration” page

Check the network settings and make any changes in the text boxes if required.

XtracontrolEC21 configuration: ETH0 = X4, ETH1 = X5

Save the settings by clicking on “Save”.

10.

Additional settings can also be viewed and/or modified on the web configuration page (e.g. system time,

display resolution, TargetVisu).

11.

In order to activate all of the modified settings, reboot the device:

Disconnect the device temporarily from the power supply
– or –
Click on “Reboot” in the web interface and then confirm on the next screen by clicking on “Reboot Module”.

The device is now configured and ready for use.

Содержание Xtracontrol DC2
























































































Результаты поиска

Содержание Xtracontrol DC2

Отзывы:

Похожие инструкции для Xtracontrol DC2

Бренды по названию

Популярные бренды

Infranor Xtracontrol DC2, Руководство пользователя

Результаты поиска

Содержание Xtracontrol DC2

Отзывы:

Похожие инструкции для Xtracontrol DC2

Бренды по названию

Популярные бренды