Infranor Xtracontrol DC2 Скачать руководство пользователя | Manualshive

Страница: 17 / 87

background image

User Manual V1.3 | XtracontrolDC2, XtracontrolET2, XtracontrolEC21

3.2

Scope of delivery and accessories

Scope of delivery

XtracontrolDC2:



Device



12-pin plug connector for digital inputs / outputs and power supply

Weidmüller BLZF 3.50/12/180



6-pin plug connector for analogue inputs

Weidmüller B2CF 3.50/06/180

XtracontrolET2



Device



2-pin. plug connector for power supply

Weidmüller BLZF 3.50/02/180

XtracontrolEC21:



Device



12-pin plug connector for digital inputs / outputs and power supply

Weidmüller BLZF 3.50/12/180



6-pin plug connector for analogue inputs

Weidmüller B2CF 3.50/06/180

Accessories



E-I/O plug, 6-pin, black



E-I/O plug, 12-pin, black



E-I/O plug, 2-pin, black

3.3

Product features

Installation

XtracontrolDC2:
The device is designed for installation in a front panel or in a control panel in a rough industrial environment.

XtracontrolET2:
The device is designed for installation in a front panel or in a control panel in a rough industrial environment.

XtracontrolEC21:
The device is designed for installation on a DIN rail (35 mm) in a control cabinet in an industrial environment with a
category 2 level of pollution.

Processor

In its basic configuration the device is equipped with an 800 MHz ARM

®

CPU with a Cortex™-A9 core. Customer-

specific variants are available, which instead of a single core processor are equipped with a dual core or quad core
processor.

Ethernet

The device has two 10/100 Mbit/s Ethernet interfaces.
The first Ethernet interface is used for standard Ethernet connections. TCP/IP and UDP/IP protocols permit flexible
connections to visualisation software, higher-level control units and to the IT infrastructure.
The second Ethernet interface is used as an EtherCAT master interface.
Other protocols available for the Ethernet interfaces: PROFINET, BACnet and Modbus.

© Infranor GmbH

17

«
...
15
16
17
18
19
...
»

Содержание Xtracontrol DC2
























































































Отзывы:

Нет отзывов

Похожие инструкции для Xtracontrol DC2

Бренд: Bang & Olufsen Страницы: 36

Бренд: Mad Catz Страницы: 4

Бренд: Federal Signal Corporation Страницы: 34

Бренд: fadini Страницы: 28

Бренд: GEA Страницы: 47

Бренд: LLURIA Страницы: 2

HmIP-FAL230-C10

Бренд: HomeMatic Страницы: 42

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренд: D+H Страницы: 16

Бренд: Joy-it Страницы: 7

Бренд: Woodward Страницы: 112

Бренд: Advantech Страницы: 2

Vizia RF+ VRP15-1LW

Бренд: Leviton Страницы: 3

Бренд: Therma-Stor Страницы: 20

Бренд: McIntosh Страницы: 68

Бренд: Cooper Страницы: 4

Бренд: Trenz Electronic Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды