Infranor Xtracontrol DC2 Скачать руководство пользователя

Страница: 22 / 87

User Manual V1.3 | XtracontrolDC2, XtracontrolET2, XtracontrolEC21

4.1.2

Installation cut-out, XtracontrolDC2.07 and XtracontrolET2.07

Fig. 8: Dimensions, XtracontrolDC2.07 and XtracontrolET2.07

Requirements:



The device must have a clear space of at least 20 mm all round at the rear, to allow sufficient air circulation.



The max. surrounding air temperature in the control cabinet must not exceed 55°C during operation.



The support material for the installation cut-out must be flat, sufficiently stable, and be from 1 to 3 mm thick.

NOTICE

Damage to the device!

Installation on uneven support material can lead to mechanical stresses

and cracks in the front face or malfunctioning of the touch screen.

▶

Make sure that the mounting points of the device are all in a

common plane, with no more than maximum ±0.5 mm variation.

Infranor GmbH

Содержание Xtracontrol DC2
























































































Результаты поиска

Содержание Xtracontrol DC2

Отзывы:

Похожие инструкции для Xtracontrol DC2

Бренды по названию

Популярные бренды

Infranor Xtracontrol DC2, Руководство пользователя

Результаты поиска

Содержание Xtracontrol DC2

Отзывы:

Похожие инструкции для Xtracontrol DC2

Бренды по названию

Популярные бренды