Infranor Xtracontrol DC2 Скачать руководство пользователя

Страница: 58 / 87

User Manual V1.3 | XtracontrolDC2, XtracontrolET2, XtracontrolEC21

6.3

Operation

6.3.1

Status displays

The status display function is dependent on the software development environment used in conjunction with the
device.

The operating status LEDs show the current status of the power supply, the module mode and any error messages.
The signals from the LEDs depend on the current operating status of the device:



CODESYS inactive: the firmware controls the LEDs.



CODESYS active: only the CODESYS runtime system (CODESYS Runtime) controls the LEDs.

Location of the operating status LEDs

The Run/Stop and Error LEDs display the system status.

Fig. 45: Location of the operating status LEDs

LED

Meaning

PWR (green)

shows that the power supply to the electronics is correct.

Run/Stop

(yellow/green/red)

shows the system statuses and CODESYS operating

statuses.

Error (red)

shows the device has been stopped due to an error.

Infranor GmbH

Содержание Xtracontrol DC2
























































































Результаты поиска

Содержание Xtracontrol DC2

Отзывы:

Похожие инструкции для Xtracontrol DC2

Бренды по названию

Популярные бренды

Infranor Xtracontrol DC2, Руководство пользователя

Результаты поиска

Содержание Xtracontrol DC2

Отзывы:

Похожие инструкции для Xtracontrol DC2

Бренды по названию

Популярные бренды