Infineon Technologies TLE5012B Скачать руководство пользователя страница 79

Страница: 79 / 105

TLE5012B

SSC Registers

User’s Manual

Rev. 1.2, 2018-02

Activation Status Register

ACSTAT

Offset

Reset Value

Activation Status Register

18EE

Field

Bits

Type

Description

Res

15:11

res

Reserved

Reset: 00011

(during operation may change to 01011

)

AS_FRST

Activation of Firmware Reset

All configuration registers retain their contents.
0

default or after execution of firmware reset.
Firmware also sets S_RST at this point.

activation of firmware reset.

Reset: 0

AS_ADCT

Enable ADC Test vector Check

Activation of this test is only allowed with deactivated
AUTOCAL. X, Y and Temp channel will be checked.
0

after execution.

activation of ADC Test vector Check.

Reset: 1

(for update buffer 0

if no update command

send before)

AS_VEC_MAG

Activation of Magnitude Check

monitoring of magnitude disabled

monitoring of magnitude enabled.

Reset: 1

(for update buffer 0

if no update command

send before)

AS_VEC_XY

Activation of X,Y Out of Limit-Check

monitoring of X,Y Out of Limit disabled

monitoring of X,Y Out of Limit enabled.

Reset: 1

(for update buffer 0

if no update command

send before)

AS_OV

Enable of DSPU Overflow Check

monitoring of DSPU Overflow disabled

monitoring of DSPU Overflow enabled.

Reset: 1

(for update buffer 0

if no update command

send before)

AS_DSPU

AS_FUSE

AS_VR

AS_RST

Reserved

AS_FRST

AS_ADCT

Reserved

AS_VEG_MAG AS_VEC_XY

AS_OV

AS_WD

Содержание TLE5012B










































































































Результаты поиска

Содержание TLE5012B

Отзывы:

Infineon Technologies TLE5012B, Руководство пользователя, Страница: 79 / 105

Результаты поиска

Содержание TLE5012B

Отзывы: