Infineon Technologies TLE5012B Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 105

Infineon Technologies TLE5012B Скачать руководство пользователя страница 76

TLE5012B

SSC Registers

User’s Manual

76

Rev. 1.2, 2018-02

NO_GMR_XY

11

ru

No valid GMR XY Values

Cyclic check of ADC input. Flag will be set as long as
error persists and is not reset by SSC read-out.
0

B

valid GMR_XY values on the ADC input and thus
on filter output.

1

B

no valid GMR_XY values on the ADC input (e.g.
test vectors).

Reset: 0

B

S_ROM

10

r

Status ROM

Check of ROM-CRC at startup. The DSPU does not start
after fail. Flag is not reset by SSC read-out. SSC (SPI)
access possible.
0

B

CRC ok.

1

B

CRC fail or running.

Reset: 0

B

S_ADCT

9

r

Status ADC-Test

1)

Check of signal path with test vectors. All test vectors are
tested at startup. The error flag will be cleared on a SSC
read-out, but will be set again at the end of the current
firmware run, if a previous ADC test failed (affects safety
word and fast SSC read-outs). So the ADC BIST needs
to be re-run and pass to actually clear this error.
Activation in operation via AS_ADCT possible.
0

B

Test vectors ok

1

B

Test vectors out of limit

Reset: 0

B

S_MAGOL

7

ru

Status Magnitude Out of Limit

Vector length’s cyclic check of X and Y values after error
compensation. The bit is updated based on the current
angle value and thus the recommendation is to read it in
update mode, if a consistent read-out is desired. The bit
is reset by a normal SSC read-out. Deactivation via
AS_VEC_MAG.
0

B

GMR-magnitude ok

1

B

GMR-magnitude out of limit

Reset: 0

B

S_XYOL

6

ru

Status X,Y Data Out of Limit

Cyclic check of X and Y raw values. This bit is updated
based on the current angle value and thus the
recommendation is to read it in update mode, if a
consistent read-out is desired. The bit is reset by a normal
SSC read-out. Deactivation via AS_VEC_XY
0

B

X,Y data ok

1

B

X,Y data out of limit (>23230 digits, <-23230 digits)

Reset: 0

B

Field

Bits

Type

Description

«
...
74
75
76
77
78
...
»

Содержание TLE5012B










































































































Отзывы:

Нет отзывов