Infineon Technologies TLE5012B Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 105

Infineon Technologies TLE5012B Скачать руководство пользователя страница 13

TLE5012B

Functional Description

User’s Manual

13

Rev. 1.2, 2018-02

2.2.5

Interfaces

Bi-directional communication with the TLE5012B is enabled by a three-wire SSC interface. In parallel to the SSC
interface, one secondary interface can be selected, which is available on the IFA, IFB, IFC pins:
•

PWM

•

Incremental Interface

•

Hall Switch Mode

•

Short PWM Code

By using pre-configured derivates (see

), the TLE5012B can also be operated with the secondary

interface only, without SSC communication.

2.2.6

Safety Features

The TLE5012B offers a multiplicity of safety features to support the Safety Integrity Level (SIL). Infineon’s sensors
that are intended for this purpose are identified by the following logo:

Figure 2-3 PRO-SIL

TM

Logo

Disclaimer

PRO-SIL™ is a Registered Trademark of Infineon Technologies AG.
The PRO-SIL™ Trademark designates Infineon products which contain SIL Supporting Features.
SIL Supporting Features are intended to support the overall System Design to reach the desired SIL (according
to IEC61508) or A-SIL (according to ISO26262) level for the Safety System with high efficiency.
SIL respectively A-SIL certification for such a System has to be reached on system level by the System
Responsible at an accredited Certification Authority.
SIL stands for Safety Integrity Level (according to IEC 61508)
A-SIL stands for Automotive-Safety Integrity Level (according to ISO 26262)

Safety features are:

•

Test vectors switchable to ADC input (activated via SSC interface)

•

Inversion or combination of filter input streams (activated via SSC interface)

•

Data transmission check via 8-bit

C

yclic

R

edundancy

C

heck (

CRC

) for SSC communcation and 4-bit CRC

nibble for SPC interface

•

Built-in Self-test (BIST) routines for ISM, CORDIC, CCU, ADCs performed at startup

•

Two independent active interfaces possible

•

Overvoltage and undervoltage detection

«
...
11
12
13
14
15
...
»

Содержание TLE5012B










































































































Отзывы:

Нет отзывов