industrie technik TH-xxxSx1 Series Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 126

background image

34/126

E09

Alarm

No alarm

No alarm

Alarm

E10

Alarm

No alarm

Alarm

No alarm

E11

Alarm

No alarm

Alarm

Alarm

E12

Alarm

Alarm

No alarm

No alarm

E13

Alarm

Alarm

No alarm

Alarm

E14

Alarm

Alarm

Alarm

No alarm

E15

Alarm

Alarm

Alarm

Alarm

If the sensors used to define the operating temperature are all faulty (open or in short circuit), the outputs are deactivated and

the fancoil is stopped.

Example:

M07

=0 sensor

AI1

used as remote sensor in combination with the internal sensor.

If sensor

AI1

is broken, the operating temperature becomes that of the internal sensor, regardless of the value of parameter

I06

.

If the internal sensor is broken, the operating temperature becomes that of sensor

AI1

, regardless of the value of parameter

I06

.

If both are broken, the operating temperature cannot be determined. Regulation is stopped.

For sensors used as automatic season changeover water sensor (2 pipe) or minimum thermostat sensor, if the sensor fails its

function is not excluded.

If a remote sensor is used as an automatic season changeover water sensor:

- in case of short circuit, the sensor temperature is considered to be high and the mode is considered to be heating.

- in case of open sensor, the sensor temperature is considered to be low and the mode is considered to be cooling.

If a remote sensor is used as the minimum thermostat:

- in case of short circuit, the sensor temperature is considered to be high and the minimum thermostat is considered to be

closed.

- in case of sensor open, the sensor temperature is considered to be low and the minimum thermostat is considered to be

open.

For input sensor

AI3

used as 0...10V (

M11

=10 and jumper JP1 set on position 0...10V) the message “

L-HI

“ (> 10V) is visual-

ized on the display B and

E08

on the display A in alarm condition.

On the alarm page message

E08

is showed.

Table of alarms (clock only for model

TH-xxCSx1

)

ECL

Clock reading error

Clock malfunction.

«
...
32
33
34
35
36
...
»

Содержание TH-xxxSx1 Series































































































































Отзывы:

Нет отзывов

Похожие инструкции для TH-xxxSx1 Series

Бренд: Watts Страницы: 2

Бренд: Canarm Страницы: 3

Бренд: Garmin Страницы: 220

Бренд: Gardena Страницы: 16

Бренд: RAKwireless Страницы: 6

Бренд: Velleman Страницы: 26

Бренд: Velleman Страницы: 32

Бренд: Velocity Страницы: 84

Бренд: Fingertips Lab Страницы: 15

Centronic SunWindControl SWC245-II

Бренд: Becker Страницы: 52

Бренд: National Instruments Страницы: 19

Бренд: HEIDENHAIN Страницы: 257

Бренд: Woodward Страницы: 32

SmarTemp Control fx

Бренд: Webasto Страницы: 8

Бренд: ICP DAS USA Страницы: 26

Бренд: National Instruments Страницы: 22

Бренд: Neets Control Страницы: 12

GAT Access 6600 Series

Бренд: Gantner Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды