IEI Technology ROCKY-6614 Скачать руководство пользователя страница 122

Страница: 122 / 204

-12

CKY-6614 WSB- Card

122

IEI

Technology, Corp

5.5.3 Hard Disk Drives

The

Hard Disk Drives

menu is similar to the

Removable Drives

BIOS Menu 21

and it

specifies the boot sequence of the available HDDs. When the menu is opened, the HDDs

connected to the system are listed as shown below:

1st Drive

[HDD: PM-(part number)]

2nd Drive

[HDD: PS-(part number)]

3rd Drive

[HDD: SM-(part number)]

4th Drive

[HDD: SM-(part number)]

NOTE:

Only the drives connected to the system will be shown. For example, if only

two HDDs are connected only “

1st Drive

” and “

2nd Drive

” will be listed.

You will then be able to select the boot sequence from the available devices. If you select

the “

1st Drive

” option a list of available HDDs will be shown. Select the first HDD you wish

the system to boot from. If you do not wish to boot from the “

1st Drive

” you may also

disable it.

5.5.4 Removable Drives

The

Removable Drives

menu (

BIOS Menu 21

) specifies the boot sequence of the

available FDDs. When the menu is opened, the FDDs connected to the system are listed

as shown below:

1st Drive

[1st FLOPPY DRIVE]

2nd Drive

[2nd FLOPPY DRIVE]

Содержание ROCKY-6614













































































































































































































Результаты поиска

Содержание ROCKY-6614

Отзывы:

Похожие инструкции для ROCKY-6614

Бренды по названию

Популярные бренды

IEI Technology ROCKY-6614, Руководство пользователя

Результаты поиска

Содержание ROCKY-6614

Отзывы:

Похожие инструкции для ROCKY-6614

Бренды по названию

Популярные бренды