IEI Technology ROCKY-6614 Скачать руководство пользователя страница 84

Страница: 84 / 204

-84

CKY-6614 WSB- Card

IEI

Technology, Corp

Primary IDE Slave

Secondary IDE Master

Secondary IDE Slave

Third IDE Master

Third IDE Slave

The IDE Configuration menu (

BIOS Menu 4

) allows you to set or change the configurations

for the IDE devices installed in the system. If an IDE device is detected, and one of the

above listed four BIOS configuration options are selected, the IDE configuration options

shown in

Section

appear.

Hard Disk Write Protect [Disabled]

The

Hard Disk Write Protect

BIOS option allows you to protect your hard disks from being

overwritten. This menu item will only be effective if the device is accessed through the

BIOS.

Disabled

(Default)

Allows hard disks to be overwritten

Enabled

Prevents hard disks from being overwritten

IDE Detect Time Out (Sec) [5]

The

IDE Detect Time Out (Sec)

BIOS option allows you to specify the maximum time (in

seconds) the AMI BIOS will search for IDE devices. This allows you to fine-tune the

settings to allow for faster boot times. The following configuration options are available.

0 seconds

5 seconds (Default)

10 seconds

15 seconds

20 seconds

25 seconds

30 seconds

35 seconds

Содержание ROCKY-6614













































































































































































































Результаты поиска

Содержание ROCKY-6614

Отзывы:

Похожие инструкции для ROCKY-6614

Бренды по названию

Популярные бренды

IEI Technology ROCKY-6614, Руководство пользователя

Результаты поиска

Содержание ROCKY-6614

Отзывы:

Похожие инструкции для ROCKY-6614

Бренды по названию

Популярные бренды