IEI Technology ROCKY-6614 Скачать руководство пользователя страница 87

Страница: 87 / 204

-87

ROCKY-6614 CPU Card

LBA Mode

: Indicates whether the LBA (Logical Block Addressing) is a

method of addressing data on a disk drive is supported or not.

Block Mode

: Block mode boosts IDE drive performance by increasing

the amount of data transferred. Only 512 bytes of data can be transferred

per interrupt if block mode is not used. Block mode allows transfers of up

to 64 KB per interrupt.

PIO Mode

: Indicates the PIO mode of the installed device.

Async DMA

: Indicates the highest Asynchronous DMA Mode that is

supported.

Ultra DMA

: Indicates the highest Synchronous DMA Mode that is

supported.

S.M.A.R.T.

: Indicates whether or not the Self-Monitoring Analysis and

Reporting Technology protocol is supported.

Type [Auto]

The

Type

BIOS option determines the type of device that the AMIBIOS attempts to boot

from after the Power-On Self-Test (POST) has completed.

Not Installed

Selecting this value prevents the BIOS from searching

for an IDE disk drive on the specified channel.

Auto

(Default)

This selection enables the BIOS to auto detect the IDE

disk drive type attached to the specified channel. This

setting should be used if an IDE hard disk drive is

attached to the specified channel.

CD/DVD

The CD/DVD option specifies that an IDE CD-ROM

drive is attached to the specified IDE channel. The

BIOS will not attempt to search for other types of IDE

disk drives on the specified channel.

ARMD

This option specifies an ATAPI Removable Media

Device. These include, but are not limited to:

ZIP

Содержание ROCKY-6614













































































































































































































Результаты поиска

Содержание ROCKY-6614

Отзывы:

Похожие инструкции для ROCKY-6614

Бренды по названию

Популярные бренды

IEI Technology ROCKY-6614, Руководство пользователя

Результаты поиска

Содержание ROCKY-6614

Отзывы:

Похожие инструкции для ROCKY-6614

Бренды по названию

Популярные бренды