IEI Technology ROCKY-6614 Скачать руководство пользователя страница 200

Страница: 200 / 204

-20

CKY-6614 WSB- Card

200

IEI

Technology, Corp

mass storage device installed on your system. At this point, insert the FDD with

the copied RAID driver files into the FDD drive. The OS will access the SATA

drives through this disk.

Step 5:

Next, select the driver for the OS you are busy installing into the system. Once

selected, press Enter.

Step 6:

The OS will start to be installed into the system with the RAID drivers and the

SATA drives will be configured as RAID drives as stipulated in the above

selection.

Step 7:

The OS will continue to be installed and the RAID on the SATA drives

configured.

Содержание ROCKY-6614













































































































































































































Результаты поиска

Содержание ROCKY-6614

Отзывы:

Похожие инструкции для ROCKY-6614

Бренды по названию

Популярные бренды

IEI Technology ROCKY-6614, Руководство пользователя

Результаты поиска

Содержание ROCKY-6614

Отзывы:

Похожие инструкции для ROCKY-6614

Бренды по названию

Популярные бренды