IEI Technology ROCKY-6614 Скачать руководство пользователя страница 83

Страница: 83 / 204

-83

ROCKY-6614 CPU Card

Secondary Slave)

Both

(Default)

Allows the system to detect both the Primary and

Secondary IDE channels including the Primary Master,

Primary Slave, Secondary Master and Secondary Slave.

Onboard PCI IDE Mode [Legacy Mode]

The

Onboard PCI IDE Mode

BIOS option allows you to set the running mode for the PCI

IDE.

Legacy Mode

(Default)

The PCI IDE mode will be the same as the IDE

mode

Native Mode

The PCI IDE mode will be the native mode

Onboard PCI S-ATA Controller

The

Onboard PCI S-ATA Controller

option allows you to set the onboard SATA controller.

If you wish to use the RAID function (see

Appendix E

) you must set this option in the

RAID

mode.

Disabled

(Default)

The onboard PCI SATA controller is disabled

Native Mode

The SATA controller is set as an IDE device with ID

at 0181h

Raid Mode

The SATA controller is set as a RAID device with ID

at 0181h

IDE Master and IDE Slave

When entering setup, BIOS auto detects the presence of IDE devices. This displays the

status of the auto detected IDE devices. The following IDE devices will be detected and are

shown in the

IDE Configuration

menu:

Primary IDE Master

Содержание ROCKY-6614













































































































































































































Результаты поиска

Содержание ROCKY-6614

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology ROCKY-6614, Руководство пользователя

Результаты поиска

Содержание ROCKY-6614

Отзывы:

Бренды по названию

Популярные бренды