IEI Technology ROCKY-6614 Скачать руководство пользователя страница 85

Страница: 85 / 204

-85

ROCKY-6614 CPU Card

The best setting to use if the onboard IDE controllers are set to a specific IDE disk drive in

the AMIBIOS is “0 seconds” and a large majority of ultra ATA hard disk drives can be

detected well within “5 seconds” (the default setting).

ATA (PI) 80Pin Cable Detection [Host & Device]

When an Ultra ATA/66, an Ultra ATA/100 or an Ultra ATA/133 IDE hard disk drive is used,

an 80-conductor ATA cable must be used. The 80-conductor ATA cable is plug compatible

with the standard 40-conductor ATA cable. The system must detect the presence of correct

cable so that the AMIBIOS can instruct the drive to run at the correct speed for the cable

type detected.

The

ATA (PI) 80Pin Cable Detection

BIOS option allows you to determine how the IDE

cable will be detected.

Host & Device

(Default)

Both the motherboard onboard IDE controller and

IDE disk drive are used to detect the type of IDE

cable used.

Host

The motherboard onboard IDE controller detects the

type of IDE cable used.

Device

The IDE disk drive to detects the type of IDE cable

used.

IDE PIO Pre-Fetch Enable [Disabled]

The

IDE PIO PreFetch Enable

BIOS Option allows you to set the IDE controller to prefetch

IDE data.

Disabled

(Default)

IDE controller cannot prefetch data

Enabled

IDE controller can prefetch data

Содержание ROCKY-6614













































































































































































































Результаты поиска

Содержание ROCKY-6614

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology ROCKY-6614, Руководство пользователя

Результаты поиска

Содержание ROCKY-6614

Отзывы:

Бренды по названию

Популярные бренды