IEI Technology ROCKY-6614 Скачать руководство пользователя страница 141

Страница: 141 / 204

-14

ROCKY-6614 CPU Card

141

6.1 Available

Software

Drivers

NOTE:

The content of the CD may vary throughout the life cycle of the product and

is subject to change without prior notice. You may visit the IEI website or

contact technical support for the latest updates.

The ROCKY-6614 CPU card has six software drivers:

AGP Driver

in the

AGP 121

directory

Realtek AC'97 CODEC driver

in the

A3.79

directory

SiS chipset driver

in the

Chipset_VGA 3.72logo

directory

The

AGP Pack driver

in the

Chipset_VGA 3.72logo

AGPPack

directory

SiS IDE driver

in the IDE R204a directory

81xx LAN Driver

(10/100 LAN) in the

LAN\81xx

directory

LAN driver

(for GbE LAN) In the

lan\RTL81698169S(B)8110S(B)\LanSetup_v1.80.635.051018

directory

RAID Utility

in the

RAID 304c

directory. The RAID Driver Installation is

fully described in

Appendix E

All four drivers can be found on the CD that came with the CPU card. To install the drivers

please follow the instructions in the sections below

6.2 AGP

Driver

Installation

To install the AGP driver, please follow the steps below:

Step 1:

Insert the CD into the system that contains the ROCKY-6614 CPU card. Open

the

AGP 121

directory and locate the icon for the

Setup

installation file. Once

located, use the mouse to move the cursor over the icon and double click the

mouse button.

Step 2:

The “

StartingInstallShield Wizard

” in

Figure 6-1

appears.

Содержание ROCKY-6614













































































































































































































Результаты поиска

Содержание ROCKY-6614

Отзывы:

IEI Technology ROCKY-6614, Руководство пользователя, Страница: 141 / 204

Результаты поиска

Содержание ROCKY-6614

Отзывы: